manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 15 Error Correction Status Module (ECSM)

MPC5602P Microcontroller Reference Manual, Rev. 4

288

Freescale Semiconductor

 

The details on the ECC registers are provided in the subsequent sections. If the design does not include 
ECC on the memories, these addresses are reserved locations within the ECSM’s programming model.

15.4.2.10 ECC Configuration Register (ECR)

The ECC Configuration Register is an 8-bit control register for specifying which types of memory errors 
are reported. In all systems with ECC, the occurrence of a non-correctable error causes the current access 
to be terminated with an error condition. In many cases, this error termination is reported directly by the 
initiating bus master. However, there are certain situations where the occurrence of this type of 
non-correctable error is not reported by the master. Examples include speculative instruction fetches, 
which are discarded due to a change-of-flow operation, and buffered operand writes. The ECC reporting 
logic in the ECSM provides an optional error interrupt mechanism to signal all non-correctable memory 
errors. In addition to the interrupt generation, the ECSM captures specific information (memory address, 
attributes and data, bus master number, etc.) that may be useful for subsequent failure analysis.

The reporting of single-bit memory corrections can only be enabled via an SoC-configurable module input 
signal. This signal is tied to 1 at SoC level and hence reporting of single-bit memory corrections is always 
enabled. While not directly accessible to a user, this capability is viewed as important for error logging and 
failure analysis.

Address: Base + 0x0043

Access: User read/write

0

1

2

3

4

5

6

7

R

0

0

ER1BR

EF1BR

0

0

ERNCR

EFNCR

W

Reset

0

0

0

0

0

0

0

0

Figure 15-9. ECC Configuration register (ECR)

Table 15-10. ECR field descriptions

Field Description

2

ER1BR

Enable RAM 1-bit Reporting
This bit can only be set if the input enable signal is asserted. This signal is tied to 1 at SoC level and 
hence reporting of single-bit memory corrections is always enabled. The occurrence of a single-bit RAM 
correction generates a ECSM ECC interrupt request as signaled by the assertion of ESR[R1BC]. The 
address, attributes and data are also captured in the REAR, RESR, REMR, REAT and REDR registers.
0 Reporting of single-bit RAM corrections disabled
1 Reporting of single-bit RAM corrections enabled

3

EF1BR

Enable Flash 1-bit Reporting
This bit can only be set if the input enable signal is asserted. This signal is tied to 1 at SoC level and 
hence reporting of single-bit memory corrections is always enabled. The occurrence of a single-bit flash 
correction generates a ECSM ECC interrupt request as signaled by the assertion of ESR[F1BC]. The 
address, attributes and data are also captured in the FEAR, FEMR, FEAT and FEDR registers.
0 Reporting of single-bit flash corrections disabled
1 Reporting of single-bit flash corrections enabled

6

ERNCR

Enable RAM Non-Correctable Reporting
The occurrence of a non-correctable multi-bit RAM error generates a ECSM ECC interrupt request as 
signaled by the assertion of ESR[RNCE]. The faulting address, attributes and data are also captured in 
the REAR, RESR, REMR, REAT and REDR registers.
0 Reporting of non-correctable RAM errors disabled
1 Reporting of non-correctable RAM errors enabled

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

ABB XFC G5 Quick Start Manual preview
XFC G5
Brand: ABB Pages: 2
Bartlett 700 Series Operation Manual preview
700 Series
Brand: Bartlett Pages: 30
Oceanic ZX Service Procedure preview
ZX
Brand: Oceanic Pages: 13
Yudian AI Series Operation Instruction Manual preview
AI Series
Brand: Yudian Pages: 26
Danfoss EKC 316A Reference Manual preview
EKC 316A
Brand: Danfoss Pages: 16
Goodson GEO-SC Instructions preview
GEO-SC
Brand: Goodson Pages: 4
Moeller TC-RMQ Installation Instructions preview
TC-RMQ
Brand: Moeller Pages: 2
Gecko MC-MP Service Manual preview
MC-MP
Brand: Gecko Pages: 82
Mosa EAS 15-806 Use And Maintenance Manual preview
EAS 15-806
Brand: Mosa Pages: 28
McIntosh MHT200 Service Manual preview
MHT200
Brand: McIntosh Pages: 60
Ruida Technology RDLC320 User Manual preview
RDLC320
Brand: Ruida Technology Pages: 45
McIntosh MHT200 Owner'S Manual preview
MHT200
Brand: McIntosh Pages: 68
ADLINK Technology PCIe-8332 User Manual preview
PCIe-8332
Brand: ADLINK Technology Pages: 37
Go Power 10 AMP RVC-MPPT User Manual preview
10 AMP RVC-MPPT
Brand: Go Power Pages: 17
KEPCO MST 488-27HT Operator'S Manual preview
MST 488-27HT
Brand: KEPCO Pages: 34
Dieffematic LINEA c400 Instructions And Recommendations For The Installer preview
LINEA c400
Brand: Dieffematic Pages: 9
Omega CN32Pt User Manual preview
CN32Pt
Brand: Omega Pages: 20
Madas RG/2MBLZ DN 80 Technical Manual preview
RG/2MBLZ DN 80
Brand: Madas Pages: 48

Brands by name

Popular brands

Load more brands