manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 17 Flash Memory

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

353

 

25-26

B0_P0_BCFG

Bank0, Port 0 Page Buffer Configuration
This field controls the configuration of the four page buffers in the PFlash controller. The buffers 
can be organized as a “pool” of available resources, or with a fixed partition between instruction 
and data buffers.

If enabled, when a buffer miss occurs, it is allocated to the least-recently-used buffer within the 
group and the just-fetched entry then marked as most-recently-used. If the Flash access is for the 
next-sequential line, the buffer is not marked as most-recently-used until the given address 
produces a buffer hit.

00 All four buffers are available for any Flash access, that is, there is no partitioning of the buffers 

based on the access type.

01 Reserved. 
10 The buffers are partitioned into two groups with buffers 0 and 1 allocated for instruction fetches 

and buffers 2 and 3 for data accesses. 

11 The buffers are partitioned into two groups with buffers 0,1,2 allocated for instruction fetches 

and buffer 3 for data accesses. 

This field is set to 2b11 by hardware reset.

27

B0_P0_DPFE

Bank0, Port 0 Data Prefetch Enable
This field enables or disables prefetching initiated by a data read access. This field is cleared by 
hardware reset.

0 No prefetching is triggered by a data read access. 
1 If page buffers are enabled (B0_P0_BFE = 1), prefetching is triggered by any data read access. 

28

B0_P0_IPFE

Bank0, Port 0 Instruction Prefetch Enable
This field enables or disables prefetching initiated by an instruction fetch read access. This field is 
set by hardware reset.

0 No prefetching is triggered by an instruction fetch read access. 
1 If page buffers are enabled (B0_P0_BFE = 1), prefetching is triggered by any instruction fetch 

read access. 

29-30

B0_P0_PFLM

Bank0, Port 0 Prefetch Limit
This field controls the prefetch algorithm used by the PFlash controller. This field defines the 
prefetch behavior. In all situations when enabled, only a single prefetch is initiated on each buffer 
miss or hit. This field is set to 2b10 by hardware reset.

00 No prefetching is performed.
01 The referenced line is prefetched on a buffer miss, that is, 

prefetch on miss

.

1

x

The referenced line is prefetched on a buffer miss, or the next sequential page is prefetched 
on a buffer hit (if not already present), that is, 

prefetch on miss or hit

.

31

B0_P0_BFE

Bank0, Port 0 Buffer Enable
This bit enables or disables page buffer read hits. It is also used to invalidate the buffers. This bit 
is set by hardware reset.

0 The page buffers are disabled from satisfying read requests, and all buffer valid bits are cleared.
1 The page buffers are enabled to satisfy read requests on hits. Buffer valid bits may be set when 

the buffers are successfully filled.

Table 17-20. PFCR0 field descriptions (continued)

Field

Description

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

Cansec H1000 Installation Manual And Instructions For Use preview
H1000
Brand: Cansec Pages: 45
Cansec CP40 Installation Manual preview
CP40
Brand: Cansec Pages: 43
Cansec MAP2 Installation Manual preview
MAP2
Brand: Cansec Pages: 32
Datapath HX4 Quick Start Manual preview
HX4
Brand: Datapath Pages: 12
Xantrex Trace C35 Installation And Operation Manual preview
Trace C35
Brand: Xantrex Pages: 56
Xantrex Freedom Sequence Owner'S Manual preview
Freedom Sequence
Brand: Xantrex Pages: 58
AAF MicroTech II UV05 Operation & Maintenance Manual preview
MicroTech II UV05
Brand: AAF Pages: 50
Xylem CentriPro Aquavar SOLO Instruction Manual preview
CentriPro Aquavar SOLO
Brand: Xylem Pages: 48
YASKAWA Z1000 CIMR-ZU*A Series Programming Manual preview
Z1000 CIMR-ZU*A Series
Brand: YASKAWA Pages: 340
ETC Echoflex ELED2 Installation Manual preview
Echoflex ELED2
Brand: ETC Pages: 8
Texas Instruments MSP430F67681 Manual preview
MSP430F67681
Brand: Texas Instruments Pages: 27
Lampert PIP 100 Operating Instructions Manual preview
PIP 100
Brand: Lampert Pages: 15
Samson 3371 Series Mounting And Operating Instructions preview
3371 Series
Brand: Samson Pages: 70
SFC SFCR-MD Operation Manual preview
SFCR-MD
Brand: SFC Pages: 48
Satel KNX-SA41 Quick Installation Manual preview
KNX-SA41
Brand: Satel Pages: 8
Powtran PR5200 011G3 User Manual preview
PR5200 011G3
Brand: Powtran Pages: 40
Calian SatService sat-nms VLC Installation Manual preview
SatService sat-nms VLC
Brand: Calian Pages: 40
E+L RK 4004 Manual preview
RK 4004
Brand: E+L Pages: 62

Brands by name

Popular brands

Load more brands