manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 22 FlexCAN

MPC5602P Microcontroller Reference Manual, Rev. 4

568

Freescale Semiconductor

 

•

Matching and arbitration are one-pass processes. If MBs are deactivated after they are scanned, no 
re-evaluation is done to determine a new match/winner. If an Rx MB with a matching ID is 
deactivated during the matching process after it was scanned, then this MB is marked as invalid to 
receive the frame, and FlexCAN will keep looking for another matching MB within the ones it has 
not scanned yet. If it can not find one, then the message will be lost. Suppose, for example, that two 
MBs have a matching ID to a received frame, and the user deactivated the first matching MB after 
FlexCAN has scanned the second. The received frame will be lost even if the second matching MB 
was “free to receive”.

•

If a Tx MB containing the lowest ID is deactivated after FlexCAN has scanned it, then FlexCAN 
will look for another winner within the MBs that it has not scanned yet. Therefore, it may transmit 
an MB with ID that may not be the lowest at the time because a lower ID might be present in one 
of the MBs that it had already scanned before the deactivation.

•

There is a point in time until which the deactivation of a Tx MB causes it not to be transmitted (end 
of move-out). After this point, it is transmitted but no interrupt is issued and the Code field is not 
updated. In order to avoid this situation, the abort procedures described in 

Section 22.4.6.1, 

“Transmission abort mechanism

 should be used.

22.4.6.3

Message Buffer lock mechanism

Besides MB deactivation, FlexCAN has another data coherence mechanism for the receive process. When 
the CPU reads the Control and Status word of an “active not empty” Rx MB, FlexCAN assumes that the 
CPU wants to read the whole MB in an atomic operation, and thus it sets an internal lock flag for that MB. 
The lock is released when the CPU reads the Free Running Timer (global unlock operation), or when it 
reads the Control and Status word of another MB. The MB locking is done to prevent a new frame to be 
written into the MB while the CPU is reading it.

NOTE

The locking mechanism only applies to Rx MBs that have a code different 
than INACTIVE (‘0000’) or EMPTY

1

 (‘0100’). Also, Tx MBs can not be 

locked. 

Suppose, for example, that the FIFO is disabled and the second and the fifth MBs of the array are 
programmed with the same ID, and FlexCAN has already received and stored messages into these two 
MBs. Suppose now that the CPU decides to read MB number 5 and at the same time another message with 
the same ID is arriving. When the CPU reads the Control and Status word of MB number 5, this MB is 
locked. The new message arrives and the matching algorithm finds out that there are no “free to receive” 
MBs, so it decides to override MB number 5. However, this MB is locked, so the new message can not be 
written there. It will remain in the SMB waiting for the MB to be unlocked, and only then will be written 
to the MB. If the MB is not unlocked in time and yet another new message with the same ID arrives, then 
the new message overwrites the one on the SMB and there will be no indication of lost messages either in 
the Code field of the MB or in the Error and Status Register.

1. In previous FlexCAN versions, reading the C/S word locked the MB even if it was EMPTY. In current FlexCAN versions, this 

behavior is maintained when the BCC bit is negated.

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

Parker ER Series Maintenance Instructions & Parts List preview
ER Series
Brand: Parker Pages: 44
Lawler 801 Installation & Maintenance Manual preview
801
Brand: Lawler Pages: 4
QTP 10900 Quick Start Manual preview
10900
Brand: QTP Pages: 2
Nice One-Max Installation And Use Instructions And Warnings preview
One-Max
Brand: Nice Pages: 32
Carel EVD mini User Manual preview
EVD mini
Brand: Carel Pages: 36
Variotech ENA3 Manual preview
ENA3
Brand: Variotech Pages: 24
Sturtevant Richmont Global 400mp User Manual preview
Global 400mp
Brand: Sturtevant Richmont Pages: 73
L&L KILNS ONE-TOUCH Operation preview
ONE-TOUCH
Brand: L&L KILNS Pages: 12
Omega Engineering Series RHCN-7000 Install And Operation Instructions preview
Series RHCN-7000
Brand: Omega Engineering Pages: 2
WAM MIC 23 Assembly Instructions preview
MIC 23
Brand: WAM Pages: 2
Zamel NC60 Quick Manual preview
NC60
Brand: Zamel Pages: 2
OCTANORM M 1497-4 User Manual preview
M 1497-4
Brand: OCTANORM Pages: 6
Danfoss MCD 600 Installation Manual preview
MCD 600
Brand: Danfoss Pages: 22
Linear Technology LTC4232 Demo Manual preview
LTC4232
Brand: Linear Technology Pages: 6
fadini Elpro S40 Manual preview
Elpro S40
Brand: fadini Pages: 40
ECO POWER AL030W Installation Instructions preview
AL030W
Brand: ECO POWER Pages: 2
Samson 3374 Mounting And Operating Instructions preview
3374
Brand: Samson Pages: 22
Trio MC508 P848 Quick Start Manual preview
MC508 P848
Brand: Trio Pages: 8

Brands by name

Popular brands

Load more brands