manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

Share
Download
NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Reference Manual Download Page 878

Chapter 36 Nexus Development Interface (NDI)

MPC5602P Microcontroller Reference Manual, Rev. 4

878

Freescale Semiconductor

 

events will not occur when an instruction would not have normally begun execution due to a higher priority 
exception at an instruction boundary.

IAC compares perform a 31-bit compare for VLE instructions. Each halfword fetched by the instruction 
fetch unit will be marked with a set of bits indicating whether an Instruction Address Compare occurred 
on that halfword. Debug exceptions will occur if enabled and a 16-bit instruction, or the first halfword of 
a 32-bit instruction, is tagged with an IAC hit. 

36.10.2 Data Address Compare Event

Data Address Compare debug events occur when enabled and execution of a load or store class instruction 
results in a data access that meets the criteria specified in the DBCR0, DBCR2, DBCR4, DAC1, DAC2, 
DVC1, and DVC2 Registers. Data address compares may specify user/supervisor mode and data space 
(MSR

DS

), along with an effective address, masked effective address, or range of effective addresses for 

comparison. This event can occur and be recorded in DBSR regardless of the setting of MSR

DE

. Two 

address compare values (DAC1, DAC2) are provided. 

NOTE

In contrast to the Power Architecture technology, Data Address Compare 
events on e200z0h do not prevent the load or store class instruction from 
completing. If a load or store class instruction completes successfully 
without a Data TLB or Data Storage interrupt, Data Address Compare 
exceptions are reported at the completion of the instruction. If the exception 
results in a precise Debug interrupt, the address value saved in DSRR0 (or 
CSRR0 if the Debug APU is disabled) is the address of the instruction 
following the load or store class instruction. For DVC DAC events, the 
exception can be imprecisely reported even further past the load or store 
class instruction generating the event (without necessarily affecting 
DBSR

IDE

) and the saved address value can point to a subsequent instruction 

past the next instruction. This occurrence is indicated in the 
DBSR

DAC_OFST

 field.

If a load or store class instruction does not complete successfully due to a 
Data Storage exception, and a Data Address Compare debug exception also 
occurs, the result is an imprecise Debug interrupt, the address value saved 
in DSRR0 (or CSRR0 if the Debug APU is disabled) is the address of the 
load or store class instruction, and the DBSR

IDE

 bit will be set. In addition 

to occurring when DBCR0

IDM

=1, this circumstance can also occur when 

DBCR0

EDM

=1.

NOTE

DAC events will not be recorded or counted if a 

lmw

 or 

stmw

 instruction is 

interrupted prior to completion by a critical input or external input interrupt.

NOTE

DAC events are not signaled on the second portion of a misaligned load or 
store that is broken up into two separate accesses.

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands