manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

Share
Download
NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Reference Manual Download Page 56

Chapter 1 Introduction

MPC5602P Microcontroller Reference Manual, Rev. 4

56

Freescale Semiconductor

 

•

Trigger generation unit configurable in sequential mode or in triggered mode

•

Each trigger can be appropriately delayed to compensate the delay of external low pass filter

•

Double buffered global trigger unit allowing eTimer synchronization and/or ADC command 
generation

•

Double buffered ADC command list pointers to minimize ADC-trigger unit update

•

Double buffered ADC conversion command list with up to 24 ADC commands

•

Each trigger capable of generating consecutive commands

•

ADC conversion command allows to control ADC channel, single or synchronous sampling, 
independent result queue selection

1.6.28

Nexus Development Interface (NDI)

The NDI (Nexus Development Interface) block is compliant with Nexus Class 1 of the IEEE-ISTO 
5001-2003 standard. This development support is supplied for MCUs without requiring external address 
and data pins for internal visibility. The NDI block is an integration of several individual Nexus blocks that 
are selected to provide the development support interface for this device. The NDI block interfaces to the 
host processor and internal busses to provide development support as per the IEEE-ISTO 5001-2003 
Nexus Class 1 standard. The development support provided includes access to the MCU’s internal memory 
map and access to the processor’s internal registers.

The NDI provides the following features:

•

Configured via the IEEE 1149.1

•

All Nexus port pins operate at V

DDIO

 (no dedicated power supply)

•

Nexus Class 1 supports Static debug

1.6.29

Cyclic redundancy check (CRC)

The CRC computing unit is dedicated to the computation of CRC off-loading the CPU. The CRC module 
features:

•

Support for CRC-16-CCITT (

x

25 protocol):

—

x

16

 + 

x

12

 + 

x

5

 + 1

•

Support for CRC-32 (Ethernet protocol):
—

x

32

 + 

x

26

 + 

x

23

 + 

x

22

 + 

x

16

 + 

x

12

 + 

x

11

 + 

x

10

 + 

x

8

 + 

x

7

 + 

x

5

 + 

x

4

 + 

x

2

 + 

x

 + 1

•

Zero wait states for each write/read operations to the CRC_CFG and CRC_INP registers at the 
maximum frequency

1.6.30

IEEE 1149.1 JTAG controller

The JTAG controller (JTAGC) block provides the means to test chip functionality and connectivity while 
remaining transparent to system logic when not in test mode. All data input to and output from the JTAGC 
block is communicated in serial format. The JTAGC block is compliant with the IEEE standard.

The JTAG controller provides the following features:

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands