manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

Share
Download
NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Reference Manual Download Page 521

Chapter 21 LIN Controller (LINFlex)

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

521

 

An interrupt is generated if the LINIER[BOIE] bit is set.

21.8.1.4

Clock gating

The LINFlex clock can be gated from the Mode Entry module (MC_ME). In UART mode, the LINFlex 
controller acknowledges a clock gating request once the data transmission and data reception are 
completed, that is, once the Transmit buffer is empty and the Receive buffer is full.

21.8.2

LIN mode

LIN mode comprises four submodes:

•

Master mode

•

Slave mode

•

Slave mode with identifier filtering

•

Slave mode with automatic resynchronization

These submodes are described in the following pages.

21.8.2.1

Master mode

In Master mode the application uses the message buffer to handle the LIN messages. Master mode is 
selected when the LINCR1[MME] bit is set.

21.8.2.1.1

LIN header transmission

According to the LIN protocol any communication on the LIN bus is triggered by the Master sending a 
header. The header is transmitted by the Master task while the data is transmitted by the Slave task of a 
node.

To transmit a header with LINFlex the application must set up the identifier, the data field length and 
configure the message (direction and checksum type) in the BIDR before requesting the header 
transmission by setting LINCR2[HTRQ].

21.8.2.1.2

Data transmission (transceiver as publisher)

When the master node is publisher of the data corresponding to the identifier sent in the header, then the 
slave task of the master has to send the data in the Response part of the LIN frame. Therefore, the 
application must provide the data to LINFlex before requesting the header transmission. The application 
stores the data in the message buffer BDR. According to the data field length, LINFlex transmits the data 
and the checksum. The application uses the BDR[CCS] bit to configure the checksum type (classic or 
enhanced) for each message.

If the response has been sent successfully, the LINSR[DTF] bit is set. In case of error, the DTF flag is not 
set and the corresponding error flag is set in the LINESR (see 

Section 21.8.2.1.6, Error handling

).

It is possible to handle frames with a Response size larger than 8 bytes of data (extended frames). If the 
data field length in the BIDR is configured with a value higher than 8 data bytes, the LINSR[DBEF] bit is 

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands