manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

Share
Download
NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Reference Manual Download Page 865

Chapter 35 IEEE 1149.1 Test Access Port Controller (JTAGC)

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

865

 

35.9

e200z0 OnCE controller

The e200z0 core OnCE controller supports a complete set of Nexus 1 debug. A complete discussion of the 
e200z0 OnCE debug features is available in the core reference manual.

35.9.1

e200z0 OnCE controller block diagram

Figure 35-6

 is a block diagram of the e200z0 OnCE block.

Figure 35-6. e200z0 OnCE block diagram

35.9.2

e200z0 OnCE controller functional description

The functional description for the e200z0 OnCE controller is the same as for the JTAGC, with the 
differences described as follows.

35.9.2.1

Enabling the TAP controller

To access the e200z0 OnCE controller, the proper JTAGC instruction needs to be loaded in the JTAGC 
instruction register, as discussed in 

Section 35.5.2.2, “TAP sharing mode.

 The e200z0 OnCE TAP 

controller may either be accessed independently or chained with the e200z1 OnCE TAP controller, such 
that the TDO output of the e200z1 TAP controller is fed into the TDI input of the e200z0 TAP controller. 
The chained configuration allows commands to be loaded into both core’s OnCE registers in one shift 
operation, so that both cores can be sent a GO command at the same time for example.

TCK

e200z0_TMS

TDI

Test Access Port (TAP) 

e200z0_TDO

Bypass Register

External Data Register

Controller

TAP Instruction Register

OnCE Mapped Debug Registers

Auxiliary Data Register

e200z0_TRST

(OnCE OCMD)

TDO Mux

Control

{

From
JTAGC

(to JTAGC)

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands