manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 18 Enhanced Direct Memory Access (eDMA)

MPC5602P Microcontroller Reference Manual, Rev. 4

406

Freescale Semiconductor

 

242–247 

0x1C [18:23]

MAJOR.LINKC

H

[0:5]

Link channel number. If channel-to-channel linking on major loop complete is 
disabled (TCD.MAJOR.E_LINK = 0) then:
 • No channel-to-channel linking (or chaining) is performed after the outer major 

loop counter is exhausted.

Otherwise
 • After the major loop counter is exhausted, the eDMA engine initiates a channel 

service request at the channel defined by MAJOR.LINKCH[0:5] by setting that 
channel’s TCD.START bit.

248 

0x1C [24]

DONE

Channel done. This flag indicates the eDMA has completed the outer major loop. It 
is set by the eDMA engine as the CITER count reaches zero; it is cleared by 
software or hardware when the channel is activated (when the channel has begun 
to be processed by the eDMA engine, not when the first data transfer occurs).

Note:

 This bit must be cleared to write the MAJOR.E_LINK or E_SG bits.

249 

0x1C [25]

ACTIVE

Channel active. This flag signals the channel is currently in execution. It is set when 
channel service begins, and is cleared by the eDMA engine as the inner minor loop 
completes or if any error condition is detected.

250 

0x1C [26]

MAJOR.E_LINK Enable channel-to-channel linking on major loop completion. As the channel 

completes the outer major loop, this flag enables the linking to another channel, 
defined by MAJOR.LINKCH[0:5]. The link target channel initiates a channel service 
request via an internal mechanism that sets the TCD.START bit of the specified 
channel. 
NOTE: To support the dynamic linking coherency model, this field is forced to zero 
when written to while the TCD.DONE bit is set.
0 The channel-to-channel linking is disabled.
1 The channel-to-channel linking is enabled.

251 

0x1C [27]

E_SG

Enable scatter/gather processing. As the channel completes the outer major loop, 
this flag enables scatter/gather processing in the current channel. If enabled, the 
eDMA engine uses DLAST_SGA as a memory pointer to a 0-modulo-32 address 
containing a 32-byte data structure that is loaded as the transfer control descriptor 
into the local memory. 
NOTE: To support the dynamic scatter/gather coherency model, this field is forced 
to zero when written to while the TCD.DONE bit is set.
0 The current channel’s TCD is “normal” format.
1 The current channel’s TCD specifies a scatter gather format. The DLAST_SGA 

field provides a memory pointer to the next TCD to be loaded into this channel 
after the outer major loop completes its execution.

252 

0x1C [28]

D_REQ

Disable hardware request. If this flag is set, the eDMA hardware automatically 
clears the corresponding EDMA_ERQL bit when the current major iteration count 
reaches zero.
0 The channel’s EDMA_ERQL bit is not affected.
1 The channel’s EDMA_ERQL bit is cleared when the outer major loop is 

complete.

Table 18-19. TCD

n

 field descriptions (continued)

Bits

Word Offset 

[n:n]

Field Name

Description

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

Echelon Excel 50 Installation Instructions Manual preview
Excel 50
Brand: Echelon Pages: 40
Fairchild 63 Installation, Operation And Maintenance Instructions preview
63
Brand: Fairchild Pages: 2
Galcon 6100 Series Installation And Operating Instructions Manual preview
6100 Series
Brand: Galcon Pages: 32
Valcom V-1092 User Manual preview
V-1092
Brand: Valcom Pages: 3
Valcom V-1092 Technical Specifications preview
V-1092
Brand: Valcom Pages: 2
UCS SYNCHRO QUASAR AC User Manual preview
SYNCHRO QUASAR AC
Brand: UCS Pages: 10
Curtis MultiMode 1214-8 Manual preview
MultiMode 1214-8
Brand: Curtis Pages: 41
Nibe Uplink Installer Manual preview
Uplink
Brand: Nibe Pages: 20
SainSmart 101-40-173 Assembly preview
101-40-173
Brand: SainSmart Pages: 17
Darco ERO-32AP-0 V1.4 Instruction Manual And Warranty Card preview
ERO-32AP-0 V1.4
Brand: Darco Pages: 14
Rainmachine Touch HD-12 Quick Start Manual preview
Touch HD-12
Brand: Rainmachine Pages: 22
Edge Electrons EDGEIQ EE-202-0050 Installation, Commissioning And Operation Manual preview
EDGEIQ EE-202-0050
Brand: Edge Electrons Pages: 32
LOVATO ELECTRIC ATL800 Installation Manual preview
ATL800
Brand: LOVATO ELECTRIC Pages: 6
MidNite Solar Brat Instructions Manual preview
Brat
Brand: MidNite Solar Pages: 24
Zennio MINiBOX 40 v3 Quick Start Manual preview
MINiBOX 40 v3
Brand: Zennio Pages: 2
Napoleon eFIRE Operating Instructions Manual preview
eFIRE
Brand: Napoleon Pages: 8
Overland Storage NEO Agility 48 10GbE Card Instructions preview
NEO Agility 48 10GbE Card
Brand: Overland Storage Pages: 4
oventrop Hydromat DP DN 20 Operating Instructions Manual preview
Hydromat DP DN 20
Brand: oventrop Pages: 40

Brands by name

Popular brands

Load more brands