Appendix 7 Operation Messages
MITSUBISHI CNC
IV - 150
Message
Details
Can't close file for dev A
- Contact the service center
Can't close file for dev B
- Contact the service center.
Can't write file for dev A
- Could not write in the file for device B.
Recheck the connection status for device A or the input/output parameter
setting.
Can't write file for dev B
- Could not write in the file for device B.
Recheck the connection status for device B or the input/output parameter
setting.
Can't seek file for dev A
- Contact the service center.
Can't seek file for dev B
- Contact the service center.
File name not designated for dev A
- A file name was not designated for device A.
File name not designated for dev B
- A file name was not designated for device B.
Can't open directory for dev A
- Could not find a directory corresponding to device A.
Can't open directory for dev B
- Could not find a directory corresponding to device B.
Different devices designated in A and B
- The same device must be designated for devices A and B, but differing devices
were designated.
Timeout error
- A timeout error occurred when communicating with the external device.
Checking
- Cannot be executed during a check
Dir create Complete
- Creation of the directory has been completed.
Can't make directory
- An error occurred while creating the directory.
Directory pass is illegal
- The designated directory path name is illegal.
Input a correct directory path name.
Data protect
- Setting, erasing, parameter setting, etc., of the various data is
prohibited, because the data protect key is validated.
Transfer complete
- The data transfer completed correctly.
Transferring
- The data is being transferred.
Parity H error
- A parity H error was detected.
Parity V error
- A parity V error was detected.
File entry over
- The No. of registration files designated in the specifications was
exceeded, so the file could not be registered.
Program No. not found in the file
- There is no program number in the selected file.
Executing format
- The formatting is being executed.
Format complete
- The formatting completed.
Format error
- The formatting failed.
Framing error
- An error occurred between the NC and the external device.
Variable conversion error
- An error occurred during the M2 macro conversion, and the conversion failed.
Summary of Contents for E70 Series
