Appendix 7 Operation Messages
MITSUBISHI CNC
IV - 156
Appendix 7.10 Editing-related Operation Messages
Message
Details
Buffer correct not possible
- Buffer correction cannot be performed for this program.
- Buffer correction was attempted during the BTR operation.
Can't write into file
- Could not write the data to the memory with the buffer correction.
Contact the service center.
Overwrite this file?(Y/N)
- Message to confirm when registering MDI
[Y] or [INPUT]: Overwrite the file.
[N]: Do not overwrite the file.
Memory over
- The program cannot be written, because the memory capacity will be exceeded.
Designated character string not found
- Could not find the search results and character string in the program.
Save current file ?(Y/N)
- Message to confirm the saving.
[Y] : Save the changes to the current file.
[N] : Do not save the changes to the current file.
A file does not exist
- An attempt was made to select and edit a non-existent file.
Executing
- Following menu's process is executing now:
"Line paste", "Line clear", "Undo", "String search", "String replace", "Miss
warning", or "Next miss".
Designated file does not exist
- An attempt was made to select and erase a non-existent file.
Erase complete
- The data erasing completed.
Can't erase designated file
- The selected file cannot currently be erased.
Designated file does not exist
- A file that does not exist was designated when file editing.
Designated file already exists
- When creating a new file, a file name was designated that alreadyexists.
Replace? (Y/N)
- Message to confirm the character string replacement.
[Y] or [INPUT]: Replace the character string.
[N]: Do not replace the character string.
File access error
- Contact the Service Center.
File open error
- The designated file is already open.
Editing
- A program is being edited on the screen.
Save the program to write it into the memory.
Program entry over
- The program could not be registered in the memory when attempted, because
the No. of registrations designated in the specifications would be exceeded.
Block char nos over
- The character number limitation in one block was exceeded.
Paste error
- Pasting was attempted within the copy range of the same file.
Copy range is inadequate
- The copy range designation is inadequate.
Check whether the designated range exists.
- The range was designated exceeding 100 lines during mass editing.
Area designation is inadequate
- The area designation is inadequate.
Check whether the designated area exists.
Designated line is out of program range
- Designation was attempted of a line No. larger than the No. of lines in the entire
program.
Summary of Contents for E70 Series
