6 Maintenance Screens
MITSUBISHI CNC
I - 396
If "#2059 zerbas" is "0" (absolute position origin point = mechanical basic position), axis will stop automatically at this
point without moving in the opposite direction and "Complete" appears at [State] and "0.000" at [Machine end].
(Note 1) To change just the basic machine coordinate zero point, set "#0 Absolute posn set" and "#2 Zero-P", and then
turn the power OFF and ON.
(Note 2) If pressing against the machine end is attempted without passing the grip point once after turning the power
ON, the operation message "Not passed on grid" will appear. Return to a point before the last grid, and then
repeat from step of pressing against the machine end stopper.
(Note 3) If the first grid point is covered by the grid mask (#2028 grmask) as a result of return to the electric basic
position, the axis stops at the next grid point.
Note that zero-point shift amount (#2027 G28sft) is invalid.
Basic machine coordinate system
zero point
Reference
position
Zero return parameter
"#2037 G53ofs"
Grid point
(electric basic
position)
"Machine end"
Machine end stopper
(Mechanical basic
position)
"#2 Zero-P" (#2059 zerbas=1)
"#2 Zero-P" (#2059 zerbas=0)
"#2 Zero-P" depends on the setting of "#2059 zerbas".
(a)
(c)
(d)
(e)
(b)
Initialization start point
Summary of Contents for E70 Series
