E70 Series Instruction Manual
4.2 Program Editing
I - 223
4.2.12 Searching for Character Strings
(Note 1) "Executing" is displayed in flickering during string search.
Operation method
(1)
Press the [String search] menu.
The menu is highlighted
.The cursor appears at the lower input area.
(2)
Set the character string to be searched for, and
press the [INPUT] key.
(Ex.) G20 [INPUT]
A search for a character string is made from the character after
the cursor position downwards.If the character string is
discovered, the cursor moves to the start of that character
string.A message appears if there is no character string
applicable to the program.Marking can be performed by adding
an option to the character string being searched for.
(Ex.) G20/MR :G20 are marked in red.
(Refer to the "Marking function" for further details.)
(3)
To continue searching, press the [INPUT] key again.
The next corresponding character string is searched for.
When reaching the end of the program, "OK to return to the top
and search?(Y/N)" message will be displayed.
To search again from the beginning, press [Y] or [INPUT] key.
To end the search, press [N] key. The highlighted menu will be
cancelled and the character string in the data setting area will
be cleared automatically.
(4)
To end the search, press the menu key.
The menu highlight returns to normal, and the character string
in the input area disappears.
The search mode is held until the menu key is pressed.
(The character string remains in the input area.)
Summary of Contents for E70 Series
