3 Setup Screens
MITSUBISHI CNC
I - 160
(Note 3) When the parameter "#8924 Meas. confirm msg" is "1", the [Offset write] menu is highlighted and the
confirmation message "OK? (Y/N)" appears.
By pressing [Y] (or [INPUT]) key at this time, the measurement value is written as the tool compensation
amount, the highlight of the [Offset write] menu is canceled and the operation message is cleared from the
screen. Also the measurement values are cleared and the highlight of the menus ([Measure X] to [Measure C])
are canceled.
If other than [Y] (or [INPUT]) key is pressed, the measurement values will not be written. At this time, the
highlight of the [Offset write] menu is cancelled and the operation message is cleared. However, the
measurement values are not cleared and the highlight of the menus ([Measure X] to [Measure C]) stay the
same.
(Note 4) When the parameter "#1124 ofsfix" is "0", the cursor moves to the next offset No. However,when "#1124
ofsfix" is "1", the cursor does not move to the next offset No.
(Note 5) When the parameter "#11017 T-ofs set at run" is "1", the tool compensation amount data can be set even
during automatic operation or operation pause.
(Note 6) If the measurement result exceeds the setting range of the tool compensation amount, the operation message
"Setting error" will appear and the offset write cannot be executed.
Summary of Contents for E70 Series
