Appendix 8 User Parameters
MITSUBISHI CNC
IV - 170
【
#1074
】
l_Sync Initial synchronous feed
Select the feedrate mode at turning ON the power or reset.
0: Asynchronous feed (feed per minute)
1: Synchronous feed (feed per revolution)
【
#1075
】
I_G00 Initial G00
Select the linear command mode at turning ON the power or reset.
0: Linear interpolation (G01 command state)
1: Positioning (G00 command state)
【
#1076
】
Abslnc ABS/INC address (for L system only)
Select the command method for the absolute and incremental commands.
0: Use G command for the absolute and incremental commands.
1: Use axis name for the absolute and incremental commands.
(The axis name in "#1013 axname" will be the absolute command, "#1014 incax" will be the
incremental command.)
When "1" is selected, using two axis names, one each for the absolute and incremental commands,
allows to issue the absolute and incremental commands appropriately to an axis.
【
#1078
】
Decpt2 Decimal point type 2
Select the increment of position commands that do not have a decimal point.
0: Minimum input command unit (follows "#1015 cunit")
1: 1mm (or 1inch) unit (For the dwell time, 1s unit is used.)
【
#1080
】
Dril_Z Specify boring axis (for M system only)
Select a fixed cycle hole drilling axis.
0: Use an axis vertical to the selected plane as hole drilling axis.
1: Use the Z axis as the hole drilling axis regardless of the selected plane.
【
#1084
】
RadErr Arc error
Set the tolerable error range when the end point deviates from the center coordinate in the circular
command.
---Setting range---
0 to 1.000 (mm)
【
#1085
】
G00Drn G00 dry run
Select whether to apply dry run (feed at manual setting speed instead of command feedrate) to the
G00 command.
0: Not apply to G00. (move at rapid traverse rate)
1: Apply to G00. (move at manual setting speed)
【
#1086
】
G0lntp G00 non-interpolation
Select the G00 travel path type.
0: Move linearly toward the end point. (interpolation type)
1: Move to the end point of each axis at the rapid traverse feedrate for each axis. (non-
interpolation)
(Note) If this parameter is set to "1", neither of the following functions will be available: rapid traverse
constant inclination acceleration/deceleration and rapid traverse constant inclination multi-step
acceleration/deceleration.
【
#1091
】
Mpoint Ignore middle point
Select how to handle the middle point during G28 and G30 reference position return.
0: Pass the middle point designated in the program and move to the reference position.
1: Ignore the middle point designated in the program and move straight to the reference position.
【
#1103
】
T_Life Validate life management
Select whether to use the tool life management.
0: Not use
1: Use
Summary of Contents for E70 Series
