E70 Series Instruction Manual
3.3 Tool Measurement
I - 143
The display will change as shown below during manual measurement.
The operating procedure of the tool radius measurement and submenu details are the same as when measuring tool
length.
(Use [T-rad. measure] instead of [T-leng measure])
Refer to "Carrying out tool length measurement" for details.
Manual measurement status display
Display
Meaning
On mea 1
This state is entered if a skip signal is input during manual measurement.
The "On mea 2" state is shifted to after deceleration stop is confirmed.
On mea 2
This is the state during the first retract operation.
The "On mea 3" state is shifted to after retracting the retract amount.
On mea 3
This is the state in which retract by the retract amount has completed.
If the skip after deceleration stop confirmation signal is ON, the status display will remain the
same.
The "On mea 0" state is shifted to when this state is reset.
On mea 4
This is the state during the second measurement.
If the skip signal is not input even after moving to the specified position, a warning will appear,
and the status display will remain the same.
The "On mea 0" state is shifted to when this state is reset
On mea 5
This state is entered when the skip signal is input during the second measurement.
The "On mea 6" state is shifted to after deceleration stop is confirmed.
On mea 6
This is the state during the second return operation.
The "On mea 0" state is shifted to after retracting the retract amount.
On mea 0
This state is entered when not in the "On mea 1" to "On mea 6" states.
Carrying out tool radius measurement
Summary of Contents for E70 Series
