5 Operation Panel Switches in Operation Mode
MITSUBISHI CNC
II - 20
5.1 Rapid Traverse Override
5.2 Cutting Feed Override
(Note 1) The dry run rate is the movement rate set by using the MANUAL FEED RATE switch by overriding the
programmed feedrate in automatic operation.
(Note 2) Refer to the section 6.5 for feedrate override applied to manual feedrate.
5.3 Spindle Override
(1) Type 1 (code method)
Using an external signal, override can be applied to the commanded rotation speed of a spindle or mill spindle in 10%
increments from 50% to 120%.
(2) Type 2 (value setting method)
Using an external signal, override can be applied to the commanded rotation speed of a spindle or mill spindle in 1%
increments from 0% to 200%.
(Note 1) Selection between type 1 and type 2 can be designated by PLC program processing.
Use the RAPID TRAVERSE OVERRIDE switch to override the rapid traverse
feedrate in automatic or manual operation.
RAPID TRAVERSE OVERRIDE is applicable to the following:
Automatic operation: G00, G27, G28, G29, G30
Manual operation: Rapid traverse, reference position return,incremental feed
Use the FEED RATE OVERRIDE switch to override the feedrate in automatic
operation (G01, G02, or G03 F command) or the manual feedrate of jog feed in
manual operation in 10% units in the range of 0% to 300%. FEED RATE
OVERRIDE is also applicable to the dry run rate in automatic operation.
This function applies override to the rotation speed of a spindle or mill spindle
assigned by the machining program command during automatic operation or by
manual operation. There are two types of override.
100
50
1
25
%
RAPID TRAVERSE OVERRIDE
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
%
FEED RATE OVERRIDE
150
160
170
180
190
200
210
220
230
240
250
260
270
280
290
300
SPINDLE OVERRIDE
%
50
60
70
80
90
100
110
120
Summary of Contents for E70 Series
