E70 Series Instruction Manual
Appendix 6.12 Program Errors (P)
IV - 129
P282 Calculation impossible
Details
The arithmetic formula is incorrect.
Remedy
- Correct the formula in the program.
P283 Divided by zero
Details
The denominator of the division is zero.
Remedy
- Correct the program so that the denominator for division in the formula is not zero.
P288 IF EXCESS
Details
Over ten times of IF statement nesting have been done.
Remedy
Correct the program so that the number of IF statement nesting does not exceed ten.
P289 IF-ENDIF MMC.
Details
An IF statement is not ended with ENDIF.
THEN/ELSE has been commanded while there is no IF command.
Remedy
- Correct the program so that IF statements are ended with ENDIFs.
- Put IF[condition] before THEN/ELSE command.
P290 IF sentence error
Details
There is an error in the "IF[<conditional>]GOTO(" statement.
Remedy
- Correct the program.
P291 WHILE sentence error
Details
There is an error in the "WHILE[<conditional>]DO(-END(" statement.
Remedy
- Correct the program.
P292 SETVN sentence error
Details
There is an error in the "SETVN(" statement when the variable name setting was made.
Remedy
- Correct the program.
- The number of characters in the variable name of the SETVN statement must be 7 or less.
P293 DO-END nesting over
Details
The number of DO-END nesting levels in the "WHILE[<conditional>]DO(-END(" statement has
exceeded 27.
Remedy
- Correct the program so that the nesting levels of the DO-END statement does not exceed 27.
P294 DO and END not paired
Details
The DOs and ENDs are not paired off properly.
Remedy
- Correct the program so that the DOs and ENDs are paired off properly.
Summary of Contents for E70 Series
