E70 Series Instruction Manual
Appendix 6.12 Program Errors (P)
IV - 141
P903 Plane chg in Normal line ctrl
Details
The plane selection command (G17, G18, or G19) was issued during normal line control.
Remedy
- Delete the plane selection command (G17, G18, or G19) from the program of the normal line control.
P920 No spec: 3D coord conv
Details
There is no specification for 3-dimensional coordinate conversion.
Remedy
- Check the specifications.
P921 Illegal G code at 3D coord
Details
The commanded G code cannot be performed during 3-dimensional coordinate conversion modal.
Remedy
- Refer to "MITSUBISHI CNC 700/70 Series Programming Manual (Machining Center System)" for
usable G commands.
- When the parameter "#8158 Init const sur spd" is enabled, disable the parameter or issue the
constant surface speed control cancel (G97) command.
P922 Illegal mode at 3D coord
Details
A 3-dimensional coordinate conversion command was issued during a modal for which 3-dimensional
coordinate conversion cannot be performed.
Remedy
- Refer to "MITSUBISHI CNC 700/70 Series Programming Manual (Machining Center System)" for
usable G commands.
P923 Illegal addr in 3D coord blk
Details
A G code and G68 was commanded in a block though the G code cannot be commanded with G68.
Remedy
- Refer to "MITSUBISHI CNC 700/70 Series Programming Manual (Machining Center System)" for
usable G commands.
P930 No spec: Tool axis compen
Details
A tool length compensation along the tool axis command was issued though it is out of specifications.
Remedy
- Check the specifications.
P931 Executing tool axis compen
Details
There is a G code that cannot be commanded during tool length compensation along the tool axis.
Remedy
- Correct the program.
P932 Rot axis parameter error
Details
There is an illegal linear axis name or rotary axis name set in the rotary axis configuration parameters.
There is an illegal setting in the parameter concerning the configuration of the inclined surface
machining axis.
Remedy
- Set the correct value and turn the power ON again.
Summary of Contents for E70 Series
