E70 Series Instruction Manual
IV - 177
【
#8011
】
INC. MAX. (for L system only)
Set the maximum value for when inputting the tool wear compensation amount in the incremental
mode.
A value exceeding this setting value cannot be set.
Absolute value of the input value is set.
(If a negative value is input, it is treated and set as a positive value.)
If "0" is input, this parameter will be disabled.
---Setting range---
0 to 999.999 (mm)
(Input setting increment applies)
【
#8012
】
G73 n
Set the return amount for G73 (step cycle).
Set the return amount for MITSUBISHI CNC special format G83.1.
---Setting range---
0 to 99999.999 (mm)
【
#8013
】
G83 n
Set the return amount for G83 (deep hole drilling cycle).
---Setting range---
0 to 99999.999 (mm)
【
#8014
】
CDZ-VALE (for L system only)
Set the screw cut up amount for G76 and G78 (thread cutting cycle).
---Setting range---
0 to 127 (0.1 lead)
【
#8015
】
CDZ-ANGLE (for L system only)
Set the screw cut up angle for G76 and G78 (thread cutting cycle).
---Setting range---
0 to 89 (°)
【
#8016
】
G71 MINIMUM (for L system only)
Set the minimum value of the last cutting amount by the rough cutting cycle (G71, G72).
The cutting amount of the last cutting will be the remainder. When the remainder is smaller than this
parameter setting, the last cycle will not be executed.
---Setting range---
0 to 999.999 (mm)
【
#8017
】
G71 DELTA-D (for L system only)
Set the change amount of the rough cutting cycle.
The rough cutting cycle (G71, G72) cutting amount repeats d+
⊿
d, d, d-
⊿
d using the value (d)
commanded with D as a reference. Set the change amount
⊿
d.
---Setting range---
0 to 999.999 (mm)
【
#8018
】
G84/G74 n
Set the retract amount m in a G84/G74/G88 pecking tapping cycle.
(Note) In the case of a normal tapping cycle, set to "0".
Summary of Contents for E70 Series
