E70 Series Instruction Manual
6.8 Diagnosis Data Collection Setting Screen
I - 409
(Note)
The alarm history can be performed its start or stop of the data collection only by setting 0 or 1 in the
"collecting data select". The alarm history can not be started or stopped by the start/stop menu.
Display item
Details
(3)
Collecting data select
This selects the diagnosis data to be collected.
(0 : Collected. 1 : Not collected.)
H/W config
This selects whether or not H/W configuration data is collected.
S/W config
This selects whether or not S/W configuration data is collected.
Key history
This selects whether or not key history data is collected.
Alarm history
This selects whether or not alarm history data is collected.
PLC I/O history
This selects whether or not PLC input/output signal history data is collected.
AC alarm history
This selects whether or not AC input power error history data is collected.
Spindle data 1
This selects whether or not spindle current waveform (speed FB, current FB, current
command, position FB, position command, droop) data is collected.
Spindle data 2
This selects whether or not spindle current waveform (driver statuses 1,3,4) data is
collected.
Servo data 1
This selects whether or not servo current waveform (speed FB, current FB, current
command, position FB, position command, droop) data is collected.
Servo data 2
This selects whether or not servo current waveform (detector position Rn, Pn) data is
collected.
Modal
This selects whether or not modal information (information for each running block (block
data, G-command modal, workpiece coordinate offset)) data is collected.
Program data
This selects whether or not program data (information for each running block (program
coordinate position, manual interruption amount, command termination)) data is collected.
Coordinate data
This selects whether or not coordinate data (information for each running block (relative
position, machine FB position, machine command position)) data is collected.
Menus
Menu
Details
Type
Reference
This begins collecting sampling data and history data.
A
6.8.1 Performing a
Data Collection
Operation
This stops the sampling data and history data collection operation.
A
6.8.2 Stopping a Data
Collection Operation
This stops the sampling data and history data collection operation, and
clears the collected data.
(Note) When the parameter "#1263 set35/bit1" is set to "1", this menu is
not displayed.
A
6.8.3 Clearing a
Collected Data
Start
Stop
Data
clear
Summary of Contents for E70 Series
