Appendix 6 Explanation of Alarms
MITSUBISHI CNC
IV - 124
P184 Pitch/thread number error
Details
- The pitch or the number of threads per inch is illegal in the tap cycle of the fixed cycle for drilling
command.
- The pitch is too small for the spindle rotation speed.
- The thread number is too large for the spindle rotation speed.
Remedy
- Correct the pitch or the number of threads per inch.
P185 No spec: Sync tapping cycle
Details
Synchronous tapping cycle (G84/G74) was commanded though it is out of specifications.
Remedy
- Check the specifications.
P186 Illegal S cmnd in synchro tap
Details
S command was issued during synchronous tapping modal.
Remedy
- Cancel the synchronous tapping before issuing the S command.
P190 No spec: Turning cycle
Details
A lathe cutting cycle command was issued though it is out of specifications.
Remedy
- Check the specification.
- Delete the lathe cutting cycle command.
P191 Taper length error
Details
In the lathe cutting cycle, the specified length of taper section is illegal.
Remedy
- Set the smaller radius value than the axis travel amount in the lathe cycle command.
P192 Chamfering error
Details
Chamfering in the thread cutting cycle is illegal.
Remedy
- Set a chamfering amount not exceeding the cycle.
P200 No spec: MRC cycle
Details
The compound type fixed cycle for turning machining I (G70 to G73) was commanded though it is out
of specifications.
Remedy
- Check the specifications.
Summary of Contents for E70 Series
