1 Operating the Setting and Display Unit
MITSUBISHI CNC
I - 14
Division : Zero division causes an error.
Square root : If the value in the parentheses is negative, an error occurs.
Triangle function : The unit of angle
θ
is degree (°).
Arc tangent : -90 < operation results < 90.
(1) Always use "=" for the first character.
(2) Do not use the following characters as the second character or last character.
Invalid as second character: * , /, )
Invalid as last character: * , /, (, +, -
(3) Make sure that the left parentheses and right parentheses are balanced.
(4) The 360° limit does not apply on the angle. SIN (500) is interpreted as SIN (140).
(5) While the Monitor screen or the Setup screen displaying, if the axis name address, M, S, T, 2nd miscellaneous
function code (B, etc.) is pressed when "=" is set in data setting area as the first character, the operation input is
given to priority. So, the window does not open, and the cursor does not move.
(6) The exponential setting, like "1.23E-4", cannot be used. The operation result is not displayed with exponential.
(7) It is not possible to set characters exceeding the number of characters which can be input to the data setting area.
(8) It is not possible to omit "0" before the decimal point, like ".5", when operation inputting. An error will occur.
(9) The accuracy is guaranteed for the calculation with 15 digits or less. The calculation with over 15 digits does not
guarantee its accuracy.
(10) The operator or the function which does not exist in the above-mentioned, such as "ASIN", cannot be used. The
operation message "Setting error" appears, and the display of the data setting area does not change.
(11) Regardless of the input setting unit and metric system/inch system, the digit numbers below the decimal point of the
operation result is seven digits or less.
Notes for using operators and functions
Restrictions
Summary of Contents for E70 Series
