E70 Series Instruction Manual
2.3 Restart Search
I - 55
2.3.5 Operation Sequence for Program Restart
There are two types of restart, type 1 and type 2.
When feed hold has been applied and reset because the tool has broken, etc., restart with Restart type 1.
(Note 1) When single block signal is OFF, the machining is restarted without stopping temporarily after the axes return
to the restart position. (The cycle starts when the automatic return by program restart is valid.)
(Note 2) Execute Reset & Rewind for resetting.
(Note 3) Restart & Search must be carried out with Restart Type 2 when the power has been turned ON again.
If Restart Type 1 is selected, "Search error" occurs.
(Note 4) Restart Search is not possible for a program with 33 or more file name characters.
Restart type 1
Machining program
Machining restart
Feed hold reset
If the tool compensation amount (tool length,
tool radius) is changed, change the tool on
tool compensation screen.
If the cycle starts when the "Automatic
return by program restart" parameter
("#1302 AutoRP") is ON, the processing is
restarted after all axes return to the restart
position at the same time.
(Refer to "2.3.10 Returning to the Restart Position")
Operation on program restart screen
The following items are displayed when
restart search is completed.
•
Remaining distance when the restart
search is completed
•
Restart position (on local coordinates)
•
Each command value of the SMTB
functions
"RP" is displayed for the axes that have
moved to the restart position. After this, the
axis does not move in either the + or -
direction.
Execute the manual numerical value command
(S,M,T,B)
(Refer to "2.3.11 Executing the MSTB Commands")
In the manual (JOG/rapid traverse) mode, move
the axes to the restart return position.
(Refer to "2.3.10 Returning to the Restart Position")
Start
Press the RESET key and suspend the present
processing.
Replace with a new tool.
Turn the program restart switch ON.
Turn the program restart switch OFF.
Return to the automatic operation mode.
Press the cycle start button.
End
Press the feed hold button and retreat to the
tool change position by manual means or MDI.
Search the block to be restarted.
(Refer to "2.3.6 Executing Restart Search (Restart type 1)")
Summary of Contents for E70 Series
