Appendix 6 Explanation of Alarms
MITSUBISHI CNC
IV - 140
P610 Illegal parameter
Details
- The parameter setting is not correct.
- G114.1 was commanded while the spindle synchronization was selected with the PLC interface
signal.
- G110 was commanded while the mixed control (cross axis control) was selected with the PLC
interface signal.
- G125 was commanded while the control axis synchronization across part systems was selected
with the PLC interface signal.
- G126 was commanded while the control axis superimposition was selected with the PLC interface
signal.
Remedy
- Correct the settings of "#1514 expLinax (Exponential function interpolation linear axis)" and "#1515
expRotax (Exponential function interpolation rotary axis)".
- Correct the program.
- Correct the parameter settings.
P611 No spec: Exponential function
Details
There is no specification for the exponential interpolation.
Remedy
- Check the specifications.
P612 Exponential function error
Details
A travel command for exponential interpolation was issued during mirror image for facing tool posts.
Remedy
- Correct the program.
P700 Illegal command value
Details
Spindle synchronization was commanded to a spindle that is not connected serially.
Remedy
- Correct the program.
- Correct the parameter settings.
P900 No spec: Normal line control
Details
A normal line control command (G40.1, G41.1, or G42.1) was issued though it is out of specifications.
Remedy
- Check the specifications.
P901 Normal line control axis G92
Details
A coordinate system preset command (G92) was issued to a normal line control axis during normal line
control.
Remedy
- Correct the program.
P902 Normal line control axis error
Details
- The normal line control axis was set to a linear axis.
- The normal line control axis was set to the linear type rotary axis II axis.
- The normal line control axis has not been set.
- The normal line control axis is the same as the plane selection axis.
Remedy
- Correct the normal line control axis setting.
Summary of Contents for E70 Series
