E70 Series Instruction Manual
1.9 Guidance Function
I - 23
(Note 1) The operation details of function that cannot be selected because of no option are also displayed on the
contents list.
(Note 2) When the
key is pressed during the contents display, the sub-contents for operation search (operation
method (2)) are displayed.
(1) If the [?] key is pressed when alarm occurs, the alarm guidance window will open.
(2) To display another operation method, select newly an operation method from the contents list. It is not possible to
jump from the parameter, operation details to other details.
(3) When the [?] key is pressed while the menu list window is displayed, the guidance window is opened after the menu
list window is closed.
(4) E70 loads guidance data from memory card when NC starts, but if the memory card is inserted after the NC has
started, NC will load guidance data at the timing as follows.
(a) When operation, parameter, or alarm guidance is displayed.
(b) When switching display type to display G code guidance on edit screen.
(c) When G code guidance is displayed during display transition.
When NC is loading guidance data, "guidance data loading" message will show up, and loading will take few
seconds to complete.
(5) Once guidance data is loaded, guidance can be shown even after the memory card is removed.
(6) When power supply is turned off guidance data will be deleted.
(7) The instructions of parameter/operation guidance are commonly used for M700V, M70V, and E70 series. This
manual is written on the assumption that all option functions are added. Confirm with the specifications manual
issued by the machine tool builder before starting use.
(4)
Move the cursor to the operation method to be
displayed by [
↓
],[
↑
],
,
keys.
Select the "Restart search - Restart type 2" with the cursor.
(5)
Press the [INPUT] key.
The operation method for "Restart search" is displayed.
Precaution
PAGE
PAGE
Summary of Contents for E70 Series
