E70 Series Instruction Manual
4.2 Program Editing
I - 215
4.2.3 Editing MDI Program
(Note 1) Before starting MDI operation, confirm that the MDI settings are completed. If "Editing" or "MDI no setting" is
displayed, the MDI operation cannot be started.
When the [INPUT] key is pressed, the head block will be searched, and the message "MDI search complete"
will appear. The setting will then be completed.
If the cursor is moved without editing, the block indicated by the cursor will be searched for when the [INPUT]
key is pressed.
(Note 2) If the [INPUT] key is pressed when the number of MDI program characters including EOB (;) and EOR (%)
exceeds 2000, "Memory capacity over" message will appear and the MDI program will not be searched for
execution.
Note that the contents edited after the MDI program is saved last will not be saved in the NC memory.
(Note 3) When "#1288 ext24/bit0 (MDI program clear)" is set to "1", the MDI programs are cleared at the following
operations, and only % programs are saved.
- When MDI operation ends
- When the power is turned ON again
- When reset is input
- When emergency stop is canceled
Regardless of the operation mode, the MDI programs are cleared.
If the above operations take place during editing the MDI programs, the MDI programs before editing will be
cleared.
Even if the [Undo] menu is pressed after clearing MDI programs, the programs before clearing will not return.
Operation method
(1)
Press the menu [MDI] .
The menu is highlighted.The MDI program is displayed from
the head of the active editing area. The cursor moves to the
head character of the program.The mode enters the overwrite
mode.
(2)
Edit the MDI program.
Refer to "4.2.6 Edit Operations" and later.
Summary of Contents for E70 Series
