5 Diagnosis Screens
MITSUBISHI CNC
I - 324
5.8.1.1 Sampling Address
Set the sampling address.
*If the set addresses exceed the specified number of channels, they will be ignored.
(1) Index No. designation
The index No. is fixed regardless of the axis configuration.
The following shows how to set the lower 6 digits of address.
(No setting for the higher 2 digits is interpreted as "00".)
Setting range (index No.)
*Setting examples for each purpose are shown below.
- For synchronized tapping : 3rd servo axis feedback (000300) - 1st spindle feedback (010000)
- For high-accuracy (roundness) : 1st servo axis feedback (000100) - 2nd servo axis feedback (000200)
- For spindle synchronization : 1st spindle feedback (010000) - 2nd spindle feedback (020000)
Index
Sampling data
Servo axis
Spindle
Unit
00
Feedback position
○
○
Refer to "Adr n output
unit" in "5.8.1
Sampling Parameter"
01
Commanded position
○
○
9B
Spindle cutting torque output
value (R6528)
-
○
1%
9C
Current feedback
(for cutting torque estimation)
-
○
0.1%
9D
Speed command
(for cutting torque estimation)
-
○
0.01r/min
9E
Flux command
(for cutting torque estimation)
-
○
0.1%
9F
Estimated disturbance torque
(after R5492)
○
-
1%/0.01%
Servo axis
1st axis
2nd axis
…
16th axis
Feedback position
000100
000200
…
001000
Commanded position
000101
000201
…
001001
Spindle
1st axis
2nd axis
…
6th axis
Feedback position
010000
020000
…
060000
Commanded position
010001
020001
…
060001
8 7 6 5 4 3 2 1
digit
digit
Application
Setting range
2,1 Sampling target index
Refer to the following table.
4,3 Servo axis index
01 to 10 (in hexadecimal)
5 Spindle index
1 to 6
6 Not used
-
8,7 Not used
-
Address
Summary of Contents for E70 Series
