E70 Series Instruction Manual
IV - 193
【
#8315
】
Barrier Type (L) (for L system only)
Select the shape of the left chuck and tailstock barrier.
0: No area
1: Chuck
2: Tailstock
【
#8316
】
Barrier Type (R) (for L system only)
Select the shape of the right chuck and tailstock barrier.
0: No area
1: Chuck
2: Tailstock
【
#8317
】
ELIV. AX. Name (for L system only)
Set the name of the delivery axis when the right chuck and tailstock barrier is movable.
When using the multi-part system method and the delivery axis is an axis in the other part system,
designate the axis including the part system as 1A, 1B or 2A, 2B. If the part system is not designated
as A and B, the set part system will be used.
---Setting range---
A/B/.. (axis name)
1A/1B/..
2A/2B/.. (with part system designated)
0: Cancel
【
#8318
】
Stock Angle (L) (for L system only)
Set the angle for the left tailstock end section.
The angle will be interpreted as 90° if there is no setting (when "0" is set).
---Setting range---
0 to 180 (°)
0: 90° (default)
【
#8319
】
Stock Angle (R) (for L system only)
Set the angle for the right tailstock end section.
The angle will be interpreted as 90° if there is no setting (when "0" is set).
---Setting range---
0 to 180 (°)
0: 90° (default)
【
#8621
】
Coord rot plane (H)
Set the plane (horizontal axis) for coordinate rotation control.
Usually, set the name of the 1st axis.
When this parameter is not set, the coordinate rotation function will not work.
---Setting range---
Axis name
【
#8622
】
Coord rot plane (V)
Set the plane (vertical axis) for coordinate rotation control.
Usually, set the name of the 2nd axis.
When this parameter is not set, the coordinate rotation function will not work.
---Setting range---
Axis name
【
#8623
】
Coord rot centr (H)
Set the center coordinates (horizontal axis) for coordinate rotation control.
---Setting range---
-999999.999 to 999999.999 (mm)
Summary of Contents for E70 Series
