E70 Series Instruction Manual
Appendix 6.1 Operation Errors (M)
IV - 51
M91 INVALID MEASUR. 0045
Details
Measurement axis illegal
Sensor has been turned ON while two or more axes are moving.
Remedy
Move a single axis when the sensor is contacted.
M91 INVALID MEASUR. 0046
Details
Measurement axis has not returned to reference position
Reference position return has not been executed on a measurement axis in an incremental system.
Remedy
Carry out the reference position return on the measurement axis before measuring the tool.
M91 INVALID MEASUR. 0089
Details
Sensor signal illegal ON
Sensor has already been ON when TLM mode is turned ON. The travel amount was so small that the
tool contacted the sensor.
Remedy
All axes are interlocked when this alarm has occurred.
Turn the TLM mode OFF or use the interlock cancel signal to move the tool off the sensor.
Ensure at least 0.1mm for the movement to the sensor.
M91 INVALID MEASUR. 9000
Details
Speed at contact is below minimum
The tool has contacted the sensor at the lower speed than set in "#1508 TLM_Fmin (Minimum speed
toward tool setter)".
Remedy
Correct the feed rate to move the tool to the sensor.
M91 INVALID MEASUR. 9001
Details
Speed at contact is over maximum
The tool has contacted the sensor at the higher speed than set in "#1509 TLM_Fmax (Maximum speed
toward tool setter)".
Remedy
Correct the feed rate to move the tool to the sensor.
M91 INVALID MEASUR. 9002
Details
Change of offset No. or sub-side selection during measurement
An offset No. or sub-side valid signal state has been changed while a sensor signal is ON or a
compensation amount is being written.
Remedy
Carry out the measurement again.
M91 INVALID MEASUR. 9003
Details
Error on response timing of sensor signal
An offset No. has been changed at the same time as a sensor's response.
Remedy
Carry out the measurement again.
Summary of Contents for E70 Series
