3 Setup Screens
MITSUBISHI CNC
I - 144
3.3.2 Tool Measurement (L system)
This is used to carry out manual tool length measurement I or II. Either one is selected depending on the setting of
measurement switch and operation mode.
Inputting an address key, such as MST, displays manual numerical value command window where manual numerical
value command is executed.
There are two types of key operation for Manual tool length measurement 1: normal operation mode and simple
operation mode, which can be selected by the parameter "#8957 T meas (L)-Simple”.
■
Manual tool length measurement I
This is the function to calculate the tool length compensation amount automatically by moving the tool to the
measurement point with manual feed. There are two types of measurement methods in manual tool length measurement
I: the basic point method and the measurement value input method. The method is selected by setting parameter "#1102
tlm".
(1) Basic point method (#1102 tlm = 0)
Obtain the tool length with the tool nose placed on the measurement point.
To carry out the basic point method, a point to place the tool nose on (measurement point) is required.
Set the measurement point beforehand.
The measurement point is either the point set in the parameter "#2015 tlml-" or the workpiece coordinate system
offset (modal), which is specified by the parameter "#1282 ext18/bit2 (tool length measurement 1 measurement
basic point selection)".
#8957
Manual tool length measurement 1 operation mode
0
Normal operation mode
1
Simple operation mode 1
2
Simple operation mode 2
#1282 ext18/bit2
Measurement point
Parameter selection method
0
The point set in the parameter "#2015 tlml-"
Workpiece coordinate system offset
selection method
1
Workpiece coordinate system offset
(modal)
Summary of Contents for E70 Series
