E70 Series Instruction Manual
4.2 Program Editing
I - 231
With G code guidance function, the commands having "G" followed by 1 or more numbers are regarded as the G code.
Thus, when "G" that is located immediately before the cursor is within the comment, the guidance will not be refreshed.
In the same manner, when a G code is commanded using variables such as "G#100" or "G#500", etc. but numbers, the
guidance will not be refreshed.
The G code that can be displayed in the guidance area is as follows.
Gnnnnnnnn.m L ll ("n", "m", and "l" are arbitrary number.)
(Note 1) As for the G codes not included in the specifications, the guidance will not be displayed even if the above
condition is met.
G codes displayed in the G code guidance area
Commanded value
Number of valid
digits
Remarks
N(intege r)
1 to 8
When including "0" before integer command value, unnecessary "0" is ignored.
m (decimal places)
0, 1
l(value commanded
using "L")
0 to 2
This is valid when "L" exists immediately after the integer command value or
decimal command value and is followed by a command value.
If the command with "L" address precedes G code, the "L" command will not be
described in the guidance.
"G" included in the comment "GCODE" is ignored, thus, G code guidance
will not be refreshed.
"G" included in the command "GOTO" is ignored, thus, G code guidance
will not be refreshed.
G code "G120" is not included in the specifications, thus, G code guidance
will not be refreshed.
The guidance for G31.1 will be displayed.
Commanded value exceeds the number of valid digits, thus, G code
guidance will not be refreshed.
The guidance not for "G10 L50" but "G10" will be displayed.
G00 X100. (GCODE) ;
N11 GOTO1 2 ;
G91 G120 X100. Y100. ;
G00000031.1 ;
G00000031.10 ;
L50 G10 ;
Summary of Contents for E70 Series
