Appendix 8 User Parameters
MITSUBISHI CNC
IV - 176
【
#8003
】
WRK COUNT LIMIT
Set the maximum number of workpiece machining.
A signal will be output to PLC when the number of machining times is counted to this limit.
---Setting range---
0 to 999999
【
#8004
】
SPEED
Set the feedrate during automatic tool length measurement.
---Setting range---
1 to 1000000 (mm/min)
【
#8005
】
ZONE r
Set the distance between the measurement point and deceleration start point.
---Setting range---
0 to 99999.999 (mm)
【
#8006
】
ZONE d
Set the tolerable range of the measurement point.
An alarm will occur when the sensor signal turns ON before the range, set by this parameter, has not
been reached from the measurement point, or when the signal does not turn ON after the range is
passed.
---Setting range---
0 to 99999.999 (mm)
【
#8007
】
OVERRIDE
Set the override value for automatic corner override.
---Setting range---
0 to 100 (%)
【
#8008
】
MAX ANGLE
Set the maximum corner opening angle where deceleration should start automatically.
When the angle is larger than this value, deceleration will not start.
---Setting range---
0 to 180 (°)
【
#8009
】
DSC. ZONE
Set the position where deceleration starts at the corner.
Designate at which length point before the corner deceleration should start.
---Setting range---
0 to 99999.999 (mm)
【
#8010
】
ABS. MAX. (for L system only)
Set the maximum value when inputting the tool wear compensation amount.
A value exceeding this setting value cannot be set.
Absolute value of the input value is set.
(If a negative value is input, it is treated and set as a positive value.)
If "0" is input, this parameter will be disabled.
---Setting range---
0 to 999.999 (mm)
(Input setting increment applies)
Summary of Contents for E70 Series
