Appendix 6 Explanation of Alarms
MITSUBISHI CNC
IV - 38
M01 Fixed pnt mode feed ax illegal 0108
Details
The axis, designated in the manual arbitrary feed, is out of specifications.
The feedrate in manual arbitrary feed mode is illegal.
Remedy
- Check for any broken wires in the axis selection signal line or the feedrate line for the manual
arbitrary feed mode.
- Check the specifications for the manual arbitrary feed mode.
M01 Block start interlock 0109
Details
An interlock signal has been input to lock the block start.
Remedy
- Correct the sequence program.
M01 Cutting block start interlock 0110
Details
An interlock signal has been input to lock the cutting block start.
Remedy
- Correct the sequence program.
M01 Restart switch ON 0111
Details
Restart switch has been turned ON and manual mode has been selected before the restart search is
completed.
Remedy
- Search the block to restart.
- Turn the restart switch OFF.
M01 Program check mode 0112
Details
The automatic start button was pressed during program check or in program check mode.
Remedy
- Press the reset button to cancel the program check mode.
M01 Auto start in buffer correct 0113
Details
The automatic start button was pressed during buffer correction.
Remedy
- Press the automatic start button after the buffer correction is completed.
M01 In reset process 0115
Details
The automatic start button was pressed during resetting or tape rewinding.
Remedy
- When rewinding the tape, wait for the winding to end, or press the reset button to stop the winding,
and then press the automatic start button.
- During resetting, wait for the resetting to end, and then press the automatic start button.
M01 Playback not possible 0117
Details
The playback switch was turned ON during editing.
Remedy
- Cancel the editing by pressing the input or previous screen key before turning ON the playback
switch.
Summary of Contents for E70 Series
