Appendix 6 Explanation of Alarms
MITSUBISHI CNC
IV - 44
M01 Auto backlash adjust illegal 0270
Details
- A measurement condition adjustment or backlash adjustment was attempted to an axis with which
automatic backlash adjustment is impossible.
- A measurement condition adjustment or backlash adjustment was attempted even though all the
axes had not reached the 1st reference position.
- The operation mode is other than memory mode.
- The slave axis of synchronous control is selected as adjustment axis.
- An attempt has been made to start an adjustment by cycle start.
Remedy
- Check the adjustment axis.
- Start the adjustment after all the axes return to the 1st reference position.
- Check the operation mode.
- Select the master axis of synchronous control as adjustment axis when adjusting the slave axis.
- Start the adjustment by automatic backlash adjustment start signal.
M01 Operating auto backlash adjust 0271
Details
An illegal operation was attempted during measurement condition adjustment or backlash adjustment.
Remedy
- Continue the operation after canceling the measurement condition adjustment and backlash
adjustment.
M01 APLC password mismatch 0280
Details
The APLC authentication password is inconsistent.
Remedy
- Contact the machine tool builder.
M01 High-cycle sampling disabled 0290
Details
- The drive unit's hardware or software does not conform to the high-cycle sampling mode.
- High-cycle data are not used even when high-cycle sampling has been set.
- High-cycle sampling was attempted while the axis targeted for high-cycle sampling was moving.
- High-cycle sampling was attempted during speed monitor mode.
- High-cycle sampling was attempted while any of the following operations is being executed: Dog-
type zero point return, absolute position setting, synchronous tapping, spindle synchronization,
hobbing, tool spindle synchronization IC.
Remedy
- The software or hardware does not conform to the function. Contact service center.
- Set data for high-cycle sampling.
- Execute high-cycle sampling after stopping the axis targeted for high-cycle sampling.
- Execute high-cycle sampling after cancelling the speed monitor mode.
- Execute high-cycle sampling after stopping the currently executed functions.
Summary of Contents for E70 Series
