3 Setup Screens
MITSUBISHI CNC
I - 120
(Note 1) The setting/display ranges are as follows based on the "#1003 iunit(Input unit)", "#1041 I_inch(Initial state
(inch))", and #11050 T-ofs digit type (Tool compensation digit type) setting combination.
When data without the decimal point is input, a set unit can be specified by the parameter "#8119 Comp. unit
switch".
(Note2)
The standard settings and display ranges are as follows.
The display range is when the minimum command unit is 1
μ
m ("#1003 iunit"= B, "#1041 I_inch" = 0, "#11050
T-ofs digit type" = 0).
CAUTION
If the tool compensation amount or workpiece coordinate system offset amount is changed during
automatic operation (including during single block stop), the changes will be valid from the command in the next
block or after several subsequent blocks.
Display items
Display item
Details
(1)
Display area
Displays the tool compensation data. The displayed cursor can be moved and data set.
Data that cannot be displayed in the display area can be displayed using the keys below.
,
: Scroll one line at a time.
,
: Change the display contents one page at a time.
Offset No.: This is the compensation data number.
Compensation data: The display items differ depending on the tool compensation type.
[Type I]
Compensation data: Amount in which the shape and wear compensations are combined
[Type II]
Length dimension: Tool length compensation amount.
Length wear: Tool length wear compensation amount.
Radius dimension: Tool radius compensation amount.
Radius wear: Tool radius wear compensation amount.
The setting/display range is different depending on the combination of the settings of "#1003 iunit"
and "#1041 I_inch". (Note 1) (Note2)
#1003
iunit
#1041
I_inch
#11050
T-ofs digit type
Setting/display range
B
0
0
-999.999 to 999.999
1
-9999.999 to 9999.999
1
0
- 99.9999 to 99.9999
1
- 999.9999 to 999.9999
C
0
0
-999.9999 to 999.9999
1
-9999.9999 to 9999.9999
1
0
- 99.99999 to 99.99999
1
- 999.99999 to 999.99999
Type
Settings
Details
Setting/display range
I
Compensation data
This sets the shape and wear combined
compensation amounts.
-999.999 to 999.999
II
Length dimension
This sets the tool length compensation amount.
-999.999 to 999.999
Length wear
This sets the tool length wear compensation
amount.
Radius dimension
This sets the tool radius compensation amount.
Radius wear
This sets the tool radius wear compensation
amount.
ً
ۂ
Summary of Contents for E70 Series
