2.5.1 Displaying the Machine Position Trace........................................................................................ 71
2.5.2 Canceling the Machine Position Trace ........................................................................................ 71
2.5.3 Changing the Display Range ....................................................................................................... 72
2.5.4 Changing the Display Mode......................................................................................................... 74
2.5.5 Changing the Display Angle......................................................................................................... 75
2.5.6 Switching the Axis Movement Direction (+, -) .............................................................................. 75
2.5.7 Switching the Full-screen Display Mode ...................................................................................... 76
2.5.8 Precautions for Tracing................................................................................................................ 76
2.6 Program Check (2D) ............................................................................................................................ 77
2.7 Counter All-axis Display ....................................................................................................................... 78
2.8 Tool Compensation Amount................................................................................................................. 80
2.9 Workpiece Coordinate System Compensation .................................................................................... 84
2.10 Counter Setting .................................................................................................................................. 85
2.11 Origin Set, Origin Cancel ................................................................................................................... 87
2.12 Manual Numerical Value Command .................................................................................................. 89
2.13 Modal Display..................................................................................................................................... 91
2.14 Program Tree Display ........................................................................................................................ 94
2.15 Integrated Time Display ..................................................................................................................... 95
2.15.1 Setting the Integrated Time........................................................................................................ 96
2.15.2 Setting the Time Display Selection ............................................................................................ 97
2.16 Common Variables............................................................................................................................. 98
2.16.1 Setting Common Variables ...................................................................................................... 100
2.16.2 Copying/Pasting Common Variables ....................................................................................... 100
2.16.3 Erasing Common Variables ..................................................................................................... 101
2.16.4 Switching the Display Area ...................................................................................................... 101
2.17 Local Variables................................................................................................................................. 102
2.17.1 Displaying the Arbitrary Local Variables .................................................................................. 104
2.18 Buffer Correction .............................................................................................................................. 105
2.19 PLC Switch Function........................................................................................................................ 109
2.19.1 Turning PLC Switches ON/OFF............................................................................................... 110
2.20 Load Meter Display .......................................................................................................................... 111
2.21 Spindle, Standby Display ................................................................................................................. 112
2.22 All Spindles' Rotation Speed Display ............................................................................................... 113
3 Setup Screens ......................................................................................................................................... 115
3.1 Screen Configuration ......................................................................................................................... 116
3.2 Tool Compensation Amount............................................................................................................... 118
3.2.1 Tool Compensation Amount (M system).................................................................................... 119
3.2.1.1 Setting the Tool Compensation Data ................................................................................. 122
3.2.1.2 Switching the Input Method for the Tool Compensation Data............................................ 124
3.2.1.3 Erasing the Tool Compensation Data ................................................................................ 125
3.2.1.4 Copying/Pasting the Tool Compensation Data .................................................................. 126
3.2.1.5 Disabling the setting of tool compensation amount ........................................................... 126
3.2.2 Tool Compensation Amount (L system)..................................................................................... 127
3.2.2.1 Wear Data.......................................................................................................................... 127
3.2.2.2 Tool Length Data ............................................................................................................... 130
3.2.2.3 Tool Nose Data .................................................................................................................. 132
3.2.2.4 Operation Method .............................................................................................................. 134
3.2.2.5 Disabling the Setting of Tool Compensation Amount ........................................................ 137
3.3 Tool Measurement ............................................................................................................................. 138
3.3.1 Tool Measurement (M system) .................................................................................................. 138
3.3.2 Tool Measurement (L system) ................................................................................................... 144
3.4 Tool Registration ................................................................................................................................ 167
3.4.1 Registering a Tool in the Magazine Pot ..................................................................................... 169
3.4.2 Setting the PLC Command ........................................................................................................ 170
3.4.3 Setting/Erasing the Tool No. of Spindle/Standby Tools ............................................................. 170
3.4.4 Erasing the Tool Registration Data ............................................................................................ 171
3.4.5 Switching the Magazines to be Displayed ................................................................................. 171
3.5 Tool Life Management ....................................................................................................................... 172
3.5.1 Displaying the Group List
(M system: Tool life management I, II / L system: Tool life management II).............................. 174
3.5.2 Displaying the Life Management Data in Group Units (M system) ............................................ 178
Summary of Contents for E70 Series
