E70 Series Instruction Manual
Appendix 6.12 Program Errors (P)
IV - 139
P601 No spec: Skip
Details
A skip command (G31) was issued though it is out of specifications.
Remedy
- Check the specifications.
P602 No spec: Multi skip
Details
A multiple skip command (G31.1, G31.2, G31.3 or G31 Pn) was issued though it is out of
specifications.
Remedy
- Check the specifications.
P603 Skip speed 0
Details
The skip speed is "0".
Remedy
- Specify the skip speed.
P604 TLM illegal axis
Details
No axis was specified in the automatic tool length measurement block. Otherwise, two or more axes
were specified.
Remedy
- Specify only one axis.
P605 T & TLM command in a block
Details
The T code is in the same block as the automatic tool length measurement block.
Remedy
- Specify the T code before the automatic tool length measurement block.
P606 T cmnd not found before TLM
Details
The T code was not yet specified in automatic tool length measurement.
Remedy
- Specify the T code before the automatic tool length measurement block.
P607 TLM illegal signal
Details
The measurement position arrival signal turned ON before the area specified by the D command or
"#8006 ZONE d". Otherwise, the signal remained OFF to the end.
Remedy
- Correct the program.
P608 Skip during radius compen
Details
A skip command was issued during radius compensation processing.
Remedy
- Issue a radius compensation cancel (G40) command or remove the skip command.
Summary of Contents for E70 Series
