4 Edit Screens
MITSUBISHI CNC
I - 228
(Note 1) When the menu [N auto add] is pressed again while the menu is highlighting, N No. additional value display
column is cleared, and N No. automatic addition is canceled.
(Note 2) The setting range is 1 to 1000. When "01" is input, "1" is set. When "0" is input, this function is canceled. When
an illegal value or 9 characters or more is input, an error will occur.
(Note 3) The additional value can be set even when the machining program has been not opened. Even if the
machining program is opened again, the additional value is not invalid.
(Note 4) This function is enabled only during regular editing of edit screen.
(Note 5) This function is disabled during mass-editing. However, the set N No. additional value in regular editing is not
cleared, and the additional value is valid during regular editing again.
(Note 6) Even if the same N No. exists by automatic addition, an error will not occur.
(Note 7) The system separately has N No. in a right area and left area of the edit screen.
(Note 8) When the previous block is leading zero like "N010", N No. automatic addition can be executed. However, "0"
is not added, and "N10" is displayed.
(1) When the previous block has N No. (When the cursor is located at the last character in the overwrite mode.)
(2) When the previous block has N No. (When the insertion mode)
(7)
Input the second block data and " ; " (EOB).
(Ex.) G92X0.Y0.Z0.;
"N120" is added behind " ; ".
(8)
Press the [INPUT] key.
The message "Editing" disappears. The program is saved.
The N No. data is automatically generated until the edit is interrupted
with the [INPUT] key.
Example when N No. is added
N100 G28 X0 Y0 Z0 ; -> Input ";" -> N100 G28 X0 Y0 Z0;N110;
N100 G28 X0 Y0 Z0 ; -> Input ";" -> N100 G28 X0 Y0 Z0 ;N110;
N100 G28 X0 Y0 Z0 ; -> Input ";" -> N100 G28 X0 Y0 Z0 ;N110;
N100 G2 8 X0 Y0 Z0 ; -> Input ";"-> N100 G2;N110 8 X0 Y0 Z0 ;
N100G28X0Y0Z0; N200G90X20.Y20.Z20.;
-> Input ";"-> N100G28X0Y0Z0;N110 N200G90X20.Y20.Z20.;
Summary of Contents for E70 Series
