E70 Series Instruction Manual
Appendix 6.12 Program Errors (P)
IV - 117
P76 No spec: 3DIM arc interpolat
Details
G02.4/G03.4 was commanded though there is no 3-dimension circular interpolation specification.
Remedy
- Check the specifications.
P80 No spec: Hypoth ax interpolat
Details
Hypothetical axis interpolation (G07) was commanded though it is out of specifications.
Remedy
- Check the specifications.
P90 No spec: Thread cutting
Details
A thread cutting command was issued though it is out of specifications.
Remedy
- Check the specifications.
P91 No spec: Var lead threading
Details
Variable lead thread cutting (G34) was commanded though it is out of specifications.
Remedy
- Check the specifications.
P93 Illegal pitch vaule
Details
An illegal thread lead (thread pitch) was specified at the thread cutting command.
Remedy
- Correct the thread lead for the thread cutting command.
P100 No spec: Cylindric interpolat
Details
A cylindrical interpolation command was issued though it is out of specifications.
Remedy
- Check the specifications.
P110 Plane select during figure rot
Details
Plane selection (G17/G18/G19) was commanded during figure rotation.
Remedy
- Correct the machining program.
P111 Plane selected while coord rot
Details
Plane selection commands (G17, G18, G19) were issued during a coordinate rotation was being
commanded.
Remedy
- Always command coordinate rotation cancel after the coordinate rotation command, and then issue
a plane selection command.
Summary of Contents for E70 Series
