5 Diagnosis Screens
MITSUBISHI CNC
I - 326
The below listed PLC devices are able to be designated.
○
: Possible / × : Not possible
*
The output contact, setting value, and present value can also be obtained for T, ST, and C devices.
The size designation is not required and bit No. designation is not possible for the following devices.
Ex) - To obtain the output contact of T703: Designate "/T1703"
- To obtain the setting value of C55: Designate "/C2055"
- To obtain the present value of ST: Designate "/ST3001"
Note 1)
A setting error occurs if a value out of the range is designated for the device No. or other PLC device
is designated.
Note 2
)
For a word device, the device No. and bit No. which can be designated differ as follows depending
on the designated size. A setting error occurs if a value out of the specification or out of the range is
designated.
Note 3
)
A setting error occurs if "/" at the head is omitted and a PLC device name is designated.
Note 4
)
A setting error occurs if the size is not designated for a word device.
Note 5
)
A setting error occurs if the size or bit is designated for a bit device.
Note 6
)
The setting of address "n" output unit is disabled when a PLC device is designated.
Note 7
)
When a PLC device is designated with a zero-filled value such as "X00001", it is handled in the
same manner as "X1".
Device
Device range
Units
Details
Bit No.
Size designation
X
X0 to X1FFF
1bit
Input signals to the PLC
×
Y
Y0 to Y1FFF
1bit
Output signals from the
PLC
×
M
M0 to M10239
1bit
Temporary memory
×
F
F0 to F1023
1bit
Temporary memory
Alarm message interface
×
L
L0 to L511
1bit
Latch relay
×
SM
SM0 to SM1023
1bit
Special relay
×
SB
SB0 to SB1FF
1bit
Special relay
×
SW
SW0 to SW1FF
16bit
Special register
○
T
※
T0 to T703
1bit
Timer
×
ST
※
ST0 to ST63
1bit
Incremented timer
×
C
※
C0 to C255
1bit
Counter
×
D
D0 to D2047
16bit
Data register
○
R
R0 to R32767
16bit
File register
○
B
B0 to B1FFF
1bit
Link relay
×
V
V0 to V255
1bit
Edge relay
×
SD
SD0 to SD1023
16bit
Special register
○
W
W0 to W1FFF
16bit
Link register
○
Device range
Units
Details
1000 + Device No.
1bit
Output contact
2000 + Device No.
16bit
Setting value
3000 + Device No.
16bit
Setting value
Size designation
Device No.
Bit No.
S
No limitation
0 to 15
D
Even number
0 to 31
Q
Multiple of 4
0 to 63
Summary of Contents for E70 Series
