6 Maintenance Screens
MITSUBISHI CNC
I - 402
Set the following parameter beforehand in the "Abs.Posit.Param." screen.
(Note 1) To change just the basic machine coordinate zero point, set "#0 Absolute posn set" and "#2 Zero-P", and then
turn the power OFF and ON.
(Note 2) If aligning axis on the marked point is attempted without passing the grip point once after turning the power
ON, the operation message "Not passed on grid" will appear. Return to a point before the last grid, and then
repeat from step of aligning the axis on the marked point.
(Note 3) If the first grid point is covered by the grid mask (#2028 grmask) as a result of return to the electric basic
position, the axis stops at the next grid point.
Note that zero-point shift amount (#2027 G28sft) is invalid.
Procedures (Marked point alignment method II)
Parameter
Setting value
#2049 type (absolute position detection type)
4 (marked point alignment method II is selected)
(1)
Select the axis that "#2049 type" is "4".
Refer to "6.6.1 Selecting the Axis" for procedures to select the
axis.
(2)
Select the HANDLE mode, HANDLE FEED AXIS
SELECT mode, or JOG mode.
(3)
Input "1" to "#0 Absolute posn set".
The input value appears at "#0 Absolute posn set".
(4)
Input an arbitrary value to "#2 Zero-P".
The input value appears at "#2 Zero-P".
Move the axis toward the mechanical basic position
and align it to the marked point.
→
a
State: [Origin Set]
Input "1" to "#1 Origin-P".
The input value appears at "#1 Origin-P".
State: [Complete]
Machine end: 0.000
Machine posn: The value set in "#2 ZERO"
Basic machine
coordinate system
zero point
Reference
position
Reference position
parameter
"#2037 G53ofs"
Initialization start point
Machine end
stopper
(mechanical
basic position)
a
"#2 Zero-P"
Summary of Contents for E70 Series
