Appendix 6 Explanation of Alarms
MITSUBISHI CNC
IV - 142
P940 No spec: Tool tip control
Details
There is no specification for tool tip center control.
Remedy
- Check the specifications.
P941 Invalid T tip control command
Details
A tool tip center control command was issued during a modal for which a tool tip center control
command cannot be issued.
Remedy
- Correct the program.
P942 Invalid cmnd during T tip ctrl
Details
A G code that cannot be commanded was issued during tool tip center control.
Remedy
- Correct the program.
P943 Tool posture command illegal
Details
In tool tip center control type 1, if the signs at the tool-side rotary axis or table base-side rotary axis
start and finish points differ, a tool base-side rotary axis or table workpiece-side rotary axis rotation
exists for the same block, and does not pass a singular point.
In tool tip center control type 2, the posture vector command is incorrect.
Remedy
- Correct the program.
P950 No spec: Tilt face machining
Details
Inclined surface machining option is not supported.
Remedy
- Check the specifications.
P951 Ill cmd in tilt face machining
Details
A forbidden command (G command, etc) was issued during inclined surface machining.
Remedy
- Check the program. If you want to execute a command (G command, etc) that is unavailable during
inclined surface machining, cancel the inclined surface machining.
P952 Inclined face cut prohibited
Details
Inclined surface machining was commanded during the mode where the machining is unavailable.
Inclined surface machining was commanded during interruption.
Remedy
- Check the program and see whether any unavailable mode is included during inclined surface
machining command. If any, cancel that mode.
P953 Tool axis dir cntrl prohibited
Details
Tool axis direction control was commanded during the mode where the control is unavailable.
Remedy
- Check the program and see whether any unavailable mode is included during tool axis direction
control. If any, cancel that mode.
Summary of Contents for E70 Series
