Appendix 8 User Parameters
MITSUBISHI CNC
IV - 198
【
#8888
】
Subbro stor D4: dev
Select the storage destination (device) for the subprogram.
M:Memory, G:HD(Note), F:FD(Note), R:Memory card, D:Data server(Note)
(Note) This is available only with M700/M700VW Series.
When D4 is designated at a subprogram call, the subprogram to be called will be searched from the
device selected with this parameter.
(Example) M98 P (program No.), D4
-> Device: "#8888 Subpro stor D4: dev" device
Directory: "#8889 Subpro stor D4: dir" directory
The device and directory above will be searched.
(Note 1) When the called subprogram is not found in the selected storage destination, a program
error will occur.
(Note 2) When D0 to D4 is not designated at a subprogram call, the subprogram will be searched
from the memory.
【
#8889
】
Subpro stor D4: dir
Select the storage destination (directory) for the subprogram.
When D4 is designated at a subprogram calling, the subprogram to be called will be searched from
the directory selected with this parameter.
Refer to "#8888 Subpro stor D4: dev".
---Setting range---
Directory 48 characters
【
#8890-8894
】
Subpro srch odr D0 to D4
Specify the search order of D0 to D4 (devices and directories storing
subprograms) when D0 to D4 are omitted from subprogram call.
Search is performed in the order from 1 to 5. When 0 is set, the device is excluded from search.
If the same value is set for more than one device, search is carried out in the order from the one with
a smaller parameter number.
If 0 is set for all the devices, the memory is searched.
---Setting range---
0 to 5
【
#8901
】
Counter type 1
Set the type of counter displayed at the upper left of the AUTO/MDI display on the Monitor screen.
1: Current position
2: Workpiece coordinate position
3: Machine position
4: Program position
8: Remain command
9: Manual interrupt amount
10: Next command
11: Restart position
12: Remain distance
16: Tip workpiece coordinate position
18: Tool axis movement
19: Tip machine position
20: Relative position
21: Table coordinate position
22: Workpiece installation position
23: Inclined surface coordinate
---Setting range---
1 to 23
Summary of Contents for E70 Series
