E70 Series Instruction Manual
6.4 System Setup Screen
I - 387
6.4.1 Writing Initial Parameters
(Note 1) When the "data protect key 2" is enabled, an operation message "Data protect" appears, and processing is
interrupted.
(Note 2) In the automatic operation mode, an operation message "Executing automatic operation" appears, and
processing is interrupted.
(Note 3) If all the required settings have not been input on the system setup screen, an operation message "Setting
error" appears, and processing is interrupted.
(Note 4) Processing is interrupted if a key other than the [Y] or [INPUT] key is pressed, or if switching to another
screen occurs. (Processing is interrupted even if switching to another screen occurs during data transfers.)
(Note 5) The menu is displayed in gray during data transfers.
(Note 6) When the inserted memory card contains the spindle parameter setting file (INITSP.PRM), the default
parameters of "Setting by spindle" set on the screen are overwritten with those from the file.
Operation methods
(1)
Enter all the required settings on the system setup
screen.
(2)
Press the menu[Param setting].
The menu is highlighted.
An operation message "Set up parameter? (Y/N)" appears.
(3)
Press the [Y] or [INPUT] key.
Parameter setting begins, and an operation message appears
as follows.
"Initial parameter creating"
→
"Initial parameter transferring"
→
"Spindle initial parameter transferring" (This operation
message is displayed only if a spindle parameter setting file
exists.)
When parameter settings are completed, an operation
message "Param set ended. Format NC memory? (Y/N)"
appears.
(4)
Press the [Y] or [INPUT] key.
File formatting begins, and an operation message "Executing
format" appears.
When file formatting is completed, an operation message
"Format complete" appears.
Summary of Contents for E70 Series
