E70 Series Instruction Manual
2.3 Restart Search
I - 61
(Note 1) When the restart switch is ON, move the axis in the same direction as the restart direction. If moved in the
reverse direction, the operation error "M01 R-pnt direction illegal" occurs. If the tool needs to be retracted
once, such as if the tool is interfering with the workpiece, turn the restart switch OFF and retract the axis
manually.
(Note 2) After restart position return is completed, the axis cannot be moved if the restart switch is ON. If the axis is
moved, the operation error "M01 restart switch ON" occurs.
(Note 3) If even one axis has not completed return to the restart position at cycle start, the error "T01 Restart pos.
return incomplete" occurs. Note that if the axis has been returned to the restart position once and is not at the
restart position during cycle start, the alarm does not occur.
(Note 4) If the axis to be returned to the restart position is a machine lock axis, the operation error "M01 program restart
machine lock" occurs. Release the machine lock before returning to the restart position.
(Note 5) If the restart switch is turned to ON after the axis is returned to the restart position with the restart switch OFF,
"PR" may not be displayed. Return to the restart position after the restart switch is turned ON.
(Note 6) After restart search had been completed, if the movement command is issued by MDI before automatic restart
position return has been started, the program error (P48) occurs. Perform the operation again after reset.
(Note 7) After restart search had been completed, if the T command different from the program is issued by MDI before
the searched program has been started, the program error (P48) may occur. Perform the operation again after
reset. T commands which result in errors are shown below. (Only L system)
(1) When "#1100 Tmove" = "0"
T command that selects a tool with different tool length/wear amount than the tool selected by the program
(2) When "#1100 Tmove" = "1"
A program error will not occur by T command.
(3) When "#1100 Tmove" = "2"
T command that selects a tool with different wear amount than the tool selected by the program
(Note 8) After restart search had been completed, if the handle interruption is performed before the searched program
has been started, always the same operation as manual absolute ON is executed regardless of "Manual
absolute" signal.
Summary of Contents for E70 Series
