5 Diagnosis Screens
MITSUBISHI CNC
I - 302
(Note)
The data only for the PLC axis indexing function. "-" is displayed in the usual axis (NC axis or during PLC axis
control) not used by the PLC axis indexing function.
AFLT gain (dB)
This displays the present filter depth of the adaptive filter.
LED display
This displays the 7-segment LED of the driver.
Alarm
This displays the alarms and warnings other than the LED display (displayed on drive unit
side).
Cycle counter (p)
This displays the position within one rotation of the encoder detector. The position is
displayed as a grid point value as "0", within one rotation in the range of "0" to "RNG
(movement units) × 1000".
Grid space
This displays the grid space for the reference position return. (Command unit)
Grid amnt
This displays the distance from the dog-off point to the grid point when the dog-type
reference position return is displayed. The grid mask amount is not included. (Command
unit)
Machine posn
This displays the NC basic machine coordinate system position. (Command unit)
Motor end FB
This displays the feedback value of the speed detector. (Command unit)
Machine end FB
This displays the feedback position of the machine end position detector. (Command unit)
FB error (i)
This displays the error of the motor end FB and machine end FB.
DFB compen amnt (i)
This displays the compensation pulse amount during dual feedback control.
Remain command
The remaining movement distance of one block is displayed. (Command unit)
Currnt posn (2)
The value of the tool compensation amount subtracted from the current position is
displayed. (Command unit)
Man int amt
The amount of interrupt movement in the manual absolute OFF state is displayed.
(Command unit)
Abs pos command
This displays the coordinates of absolute position excluding the machine error
compensation amount. (Command unit)
AUX current sta No. (Note)
This displays the current station No.
AUX current posn (Note)
This displays the current coordinates position.
AUX inst station No. (Note)
This displays the command station No. of automatic operation or the nearest station No. to
stop by manual operation etc.
AUX inst posn (Note)
This displays the coordinates position corresponding to target station No.
Mach err comp val
This displays the machine error compensation amount. (Command unit)
Display item
Details
Summary of Contents for E70 Series
