E70 Series Instruction Manual
6.16 Manual/Automatic Synchronous Feed
II - 35
6.16.5 Other Precautions
(1) If only the automatic operation mode is selected and the manual operation mode is not selected, the "Manual/
Automatic simultaneous valid n-th axis" signal will be invalid.
(2) Even if one automatic operation mode and one manual operation mode are selected, valid manual operation to an
axis for which the "Manual/Automatic simultaneous valid n-th axis" signal is turned OFF is limited to handle-feed
interruption only.
(3) If the "Manual/Automatic simultaneous valid n-th axis" signal is ON for the 1st and 2nd axes and the "Circular feed
in manual mode valid" signal is turned ON during automatic operation, the manual arc feed will not be validated.
If automatic operation is attempted while manual arc feed is valid, the manual arc feed will be invalidated even if the
"Manual/Automatic simultaneous valid n-th axis" signal for the 1st and 2nd axes is ON. In this case, none of the
axes can be moved with manual operation until the "Circular feed in manual mode valid" signal is turned OFF.
(4) The "Manual/Automatic simultaneous valid n-th axis" signal is invalid for the chopping axis during chopping.
(5) Manual random feed will not be executed if even one axis other than the manual/automatic simultaneous valid axis
is set as the manual random feed axis. Note that only the manual/automatic simultaneous valid axis is executed
during non-interpolation.
(6) When the manual mode is selected for the manual/automatic simultaneous valid axis while moving in the automatic
high-accuracy mode, if the axis is moved manually before the automatic operation decelerates to a stop with the
interlock, the speed may change in steps when the manual movement is started.
Start manual operation after the automatic operation has decelerated to a stop.
Summary of Contents for E70 Series
