background image

D9000/D7000 Series Control/Communicator

Installation and Troubleshooting Quick Reference

Basic Troubleshooting ............................................................. 2

Service Walk Test Shows Extra Points ................................ 2
Problems with Points ............................................................ 4
Problems Programming the Panel ........................................ 7
Phone Line Trouble ............................................................... 8
Communications Failure ....................................................... 8

System Wiring Diagrams, Issue A ......................................... 10

D9412 Control/Communicator ............................................. 10
D9112 Control Communicator ............................................. 11
D7412 Control/Communicator ............................................. 12
D7212 Control/Communicator ............................................. 13

Quick Reference Terminal Description .................................. 14

Introduction

This reference contains the very basic information a trained installer needs to install and
troubleshoot a D9000/D7000 Series Control/Communicator system. See the D9000/D7000
Series Operation and Installation Manual (74-07692-000) and the D9000/D7000 Series
Approved Applications Compliance Guide (74-07693-000) for a complete description of the
D9000/D7000 Series Control/Communicator and detailed installation instructions.

33317D  4/97

www.PDF-Zoo.com

firealarmresources.com

Summary of Contents for D9000 Series















Reviews: