E70 Series Instruction Manual
6.2 Input/Output Screen
I - 357
(3) Notes when transferring tool offset data files
(a) If an error occurs during offset data transfer, an error message appears on the screen, and the transfer
operation is interrupted.
(b) Tool offset data file cannot be transferred from the serial to the memory.
(4) Notes when transferring parameter files
(a) In the same manner as when setting in the Parameter screen, there are parameters validated immediately
after input, and parameters validated after a restart. Restart when a parameter file has been transferred to the
NC memory.
(b) When a parameter file is transferred to the NC memory, the setting value of the input/output parameters is also
changed. Before transferring next time, set the input/output parameters again.
(5) Notes when transferring common variable data files
(a) If the variable value is 100000 or more or less than 0.0001 when transferring common variable data, it is
expressed with an exponential expression.
(6) Notes when transferring tool life data files
(a) When tool life data is output from the NC memory, the file information is inserted at the first and last of the file.
First file information:Number of registered tools (P No.) and the maximum number of possible registrations (T
No.)
Last file information:Finish code
(7) Notes when transferring sampling data file
(a) When the output form is set as 8-digit hexadecimal number and the parameter
"#1004 ctrlunit" is set to "E (1nm)", accurate data can be output just within 1m.
When the output data length exceeds 1m, lower 32 bits of the sampling data will be output.
(8) Notes when transferring workpiece offset data files
(a) Tool offset data file cannot be transferred from the serial to the memory.
Summary of Contents for E70 Series
