Appendix 7 Operation Messages
MITSUBISHI CNC
IV - 162
Appendix 7.15 System Setup-related Operation Messages
Appendix 7.16 Automatic Backup-related Operation Messages
Message
Details
Initial parameter creating
- The initial parameter is being created.
Initial parameter transferring
- The initial parameter is being transferred.
Spindle initial parameter transferring
- The spindle initial parameter is being transferred.
Can't write data
- The data cannot be written.
- Setting of the initial parameter failed.
- Contact the service center.
Param set ended.
Format NC memory? (Y/N)
- After completing the parameter setting, it determines whether executing the
file format or not.
Enter [Y] or [INPUT] to execute the file format.
Write sample ladder? (Y/N)
- It determines whether executing writing the sample PLC program or not. Enter
[Y] or [INPUT] to start writing the sample PLC program.
Sample ladder not found
- The file to set the sample PLC program is lost.
Contact the service center.
Message
Details
Auto backup disabled
(Device illegal)
- Set a correct value in the device No. of the automatic backup device.
Auto backup disabled (No DS)
- When turning ON the power next time, insert DS.
Auto backup disabled
(No memory card)
- When turning ON the power next time, insert the memory card.
Auto backup disabled
(No USB memory)
- When turning ON the power next time,insert the USB memory.
Auto backup proceeding
- Wait for the automatic backup to complete.
Auto backup completed
- The automatic back up is completed.
Memory over
- The memory capacity of the transfer designation device was exceeded during
the automatic backup. Increase the available memory of the transfer
designation device.
File access error
- A file access error occurred during the automatic backup. Contact the service
center.
Can't make directory
- The storage destination directory of the automatic backup data described in
the custom definition file does not exist. Create the directory of the storage
destination.
Write protect
- The memory card is write-protected. Release the write protection.
Summary of Contents for E70 Series
